Nick's Build/Installation Thread
08-02-2008, 02:13 PM
#1
Junior Member
Thread Starter
iTrader: (1)
Join Date: Oct 2005
Location: Charlotte, NC
Posts: 466
Total Cats: 0
Nick's Build/Installation Thread
Due to problems with the short nose crank in the old motor i proceeded to throw in the new one with a built block. Due to class, work, and other time constraints I will be updating this thread once a week over a span of three hopefully.
Engine specs: Has also been milled .40 over, balance, polish, and coated calico bearings.
-Carrillo rods (1.6)
-Wiseco pistons
-Bill's oil pump gears
-Cometic metal head gasket (deciding if i should run this or an OEM unit)
-Gates timing belt
-new seals, gaskets, ARP main/head stud kits
-new waterpump
Before Pictures:
Engine specs: Has also been milled .40 over, balance, polish, and coated calico bearings.
-Carrillo rods (1.6)
-Wiseco pistons
-Bill's oil pump gears
-Cometic metal head gasket (deciding if i should run this or an OEM unit)
-Gates timing belt
-new seals, gaskets, ARP main/head stud kits
-new waterpump
Before Pictures:
Last edited by JDMAflac; 08-04-2008 at 01:23 PM.
Reply
0
0
08-02-2008, 02:16 PM
#2
Junior Member
Thread Starter
iTrader: (1)
Join Date: Oct 2005
Location: Charlotte, NC
Posts: 466
Total Cats: 0
Week 1 Progress:
Old meets new:
I need to go source another long transmission bolt so I can get it on the engine stand. I need to find pictures of the block with the guts installed. Also need to get my old head decked.
Week 2's progress should consist of:
-stripping the engine bay
-wire tuck
-scotch red the bay, then on with the paint
-possible installation of the NB rear top hats
Old meets new:
I need to go source another long transmission bolt so I can get it on the engine stand. I need to find pictures of the block with the guts installed. Also need to get my old head decked.
Week 2's progress should consist of:
-stripping the engine bay
-wire tuck
-scotch red the bay, then on with the paint
-possible installation of the NB rear top hats
Last edited by JDMAflac; 08-02-2008 at 09:31 PM.
Reply
0
0
08-02-2008, 09:32 PM
#3
Good stuff man. I cant wait to get to that point. How much did the motor work run ya and more importantly who built it?
Also, I hope at some point you put some new tires on the car b4 it hits the roads.
__________________
Best Car Insurance | Auto Protection Today | FREE Trade-In Quote
Also, I hope at some point you put some new tires on the car b4 it hits the roads.
__________________
Best Car Insurance | Auto Protection Today | FREE Trade-In Quote
Reply
0
0
08-02-2008, 09:39 PM
#4
Junior Member
Thread Starter
iTrader: (1)
Join Date: Oct 2005
Location: Charlotte, NC
Posts: 466
Total Cats: 0
Bought the motor off my friend who's in the picture, gave me a deal. He spent $5000 including labor/parts. Work was done by someone with 5+ years of experience I believe. I have RS2 225-45's sitting here waiting.
Reply
0
0
08-04-2008, 01:18 PM
#9
You bastard, I knew you were gonna go for it...if it was a 1.8 I would have got it instead if nothing but just to save time...You know how long it took Brad to build it.
Hooray for progress, when you guys are done, I'll hand you over my car to do the same for me...thanks!
Hooray for progress, when you guys are done, I'll hand you over my car to do the same for me...thanks!
Reply
0
0
08-05-2008, 01:34 PM
#14
Junior Member
Thread Starter
iTrader: (1)
Join Date: Oct 2005
Location: Charlotte, NC
Posts: 466
Total Cats: 0
Zabac: It fell into my lap at the right time when my motor let go.
Rappadan: Buy me a racing beat bumper and i'll consider it
Hustler: Previous owner neglected it plus my t fitting on the oil feed line leaked.
Rappadan: Buy me a racing beat bumper and i'll consider it
Hustler: Previous owner neglected it plus my t fitting on the oil feed line leaked.
Reply
0
0
08-10-2008, 04:49 PM
#15
Junior Member
Thread Starter
iTrader: (1)
Join Date: Oct 2005
Location: Charlotte, NC
Posts: 466
Total Cats: 0
Week 2's progress:
-Took out headlights and electrical components
-Bombard engine bay and steering rack with Simple Green and proceed to scrub for 2 hours
-Take off front bumper/fenders/wheels
-Let Brad do his magic on the wire tuck
-Scotch Red engine bay
-Primer and use "Chassis Black" paint
On with the pictures:
Passenger
Driver
Caked with oil/grease!!
Sanding with Gojo works wonders
-Took out headlights and electrical components
-Bombard engine bay and steering rack with Simple Green and proceed to scrub for 2 hours
-Take off front bumper/fenders/wheels
-Let Brad do his magic on the wire tuck
-Scotch Red engine bay
-Primer and use "Chassis Black" paint
On with the pictures:
Passenger
Driver
Caked with oil/grease!!
Sanding with Gojo works wonders
Reply
0
0
08-11-2008, 12:01 AM
#20
Looks like the normal 1.6 piece to me. Just has a nice paint job.
__________________
Best Car Insurance | Auto Protection Today | FREE Trade-In Quote
Reply
0
0
