Compressor surge
My car is up and running fairly well ATM. The only problem I am having is compressor surge when I let off the throttle fast. I have a HKS BOV and it seems to be functioning as it should. The surge only lasts a second or so then you only hear the BOV, so I am thinking it is the BOV not releasing pressure soon enough. I have been trying to get a good video of it to let someone hear but I have been unable to get one.
BOV source is nipple on top of the TB and WG source is off the IC pipes pre IC. Any ideas would be great. |
I was having that problem until I took my BOV apart and cleaned it all up. Mine was sticking closed. Once it would break the seal it would open freely.
|
do you have compressor surge or is your BOV fluttering?
|
Originally Posted by Braineack
(Post 389006)
do you have compressor surge or is your BOV fluttering?
And I do know what surge sounds like. I ran the Greddy kit with no BOV for awhile. I'll check what skidude said and see if that helps any. |
begi diverter / bov > *
|
I know this is kind of old but I have continued to check into this. I have checked the BOV with a compressor to see if it sticks any. I am guessing it simply can't vent enough air to avoid compressor surge even though it worked fine for my Greddy turbo.
I would think a SSQ BOV would be good enough for such small turbos that most of us are running, but I guess not. Maybe it's just because mine is old.... |
Originally Posted by DXO
(Post 394636)
I know this is kind of old but I have continued to check into this. I have checked the BOV with a compressor to see if it sticks any. I am guessing it simply can't vent enough air to avoid compressor surge even though it worked fine for my Greddy turbo.
I would think a SSQ BOV would be good enough for such small turbos that most of us are running, but I guess not. Maybe it's just because mine is old.... You getting correct vacuum? How many pounds of boost are you running? Also, where's the BOV located? |
Originally Posted by gompers
(Post 394637)
You getting correct vacuum?
How many pounds of boost are you running? Also, where's the BOV located? 18-21 VAC. BOV is on the run up from the intercooler to the TB. ATM I am only running 7 psi, the same I was running with my Greddy turbo, till I solve this surge issue. |
Originally Posted by DXO
(Post 394636)
I know this is kind of old but I have continued to check into this. I have checked the BOV with a compressor to see if it sticks any. I am guessing it simply can't vent enough air to avoid compressor surge even though it worked fine for my Greddy turbo.
I would think a SSQ BOV would be good enough for such small turbos that most of us are running, but I guess not. Maybe it's just because mine is old.... |
Well I am asking around to see if I can find another to put on for a little bit to see if it is the valve or if the problem is else where...
|
I had that bov and had the same problem no matter what I did I went with the CX racing greddy knock off and it works far better.
|
just took mine for its first boosted test drive i also am getting abit of serge before the bov opens you can really notice it when at a standstill and opening and closing the throttle. i have checked the bov and regreased it but i think the spring in it is too hard even with it adjusted right out it is a sard R2D2 guess ill give another one a go and see if i helps
|
I had an older HKS SSQV. It would only open under higher pressures. I got a new SSQV from HKS, and it is now working properly. I still get a slight surge(turkey gobbling through the intake). Honestly, I don't worry about it at all. A little surge never hurt anything.
|
I'm tempted to say that it does that on purpose. It along with the RFL and Type S (among others) are BOVs that are designed to put the noise they make over functionality IMO. I doubt it's enough to cause much damage if at all, especially at a boost level that low..in fact, under 10 psi one could say any BOV/BPV is unnecessary, especially with a good strong turbo like a 16G.
At that level, I doubt the HKS is loose enough anyways. I think they (and most other ones) are meant for more pressure, so it acts like it isnt even there under X amount of pressure. |
I installed the SSQV on my turbo build and so far no compressor surge. Works flawlessly for me.
|
All times are GMT -4. The time now is 05:29 AM. |
© 2024 MH Sub I, LLC dba Internet Brands