DIY Turbo Discussion greddy on a 1.8? homebrew kit?

Injector compatibility, measurements, etc.

Thread Tools
 
Search this Thread
 
Old 08-31-2010, 05:21 PM
  #1  
Senior Member
Thread Starter
iTrader: (3)
 
chance91's Avatar
 
Join Date: May 2008
Location: Fargo, ND
Posts: 533
Total Cats: 3
Default Injector compatibility, measurements, etc.

Hey all.

So, I was looking at PnP fuel injectors for not a whole lot of reasons earlier and came across this.

http://issuu.com/zageturbo/docs/fuel-injector

Really simple flow rating, body length, high/low impedence, and etc listing of injectors for reference.

I took some measurements so far and I have a set of 420 rx8s that I've run, I have a set of 315cc Supras I have run, and a set of 550 rx7s and a set of 2xx somethings from an mr2 as well. They are all between about 70mm and 80mm, the Rx7 is the longest because of the pintle cap length, but they all seem to have the same top to seat length.

Mainly I'm looking at the 73mm Orange 320cc injectors and the honda nissan subaru light green bodied injectors. Both would be really nice to use on a miata, either stock ecu (MSM) or aftermarket with the larger ones.

Reason I'm looking at these is you'll notice the slim body. These are a lot newer design injector than the old pintle style injectors. Out of all the ones I listed, the Rx-8 420cc injectors that I've used Idle fantastically compared to all the others, just worlds better.

So, anyone tried any of these, or willing to? What other parameters are needed to verify they will work before hand? I.E. timing, resistance, etc?

Thanks, I'm trying to find my caliper or a ******* measuring device in MM but all I have is engineering std bullshit right now. I'm really angry about this.
chance91 is offline  
Old 08-31-2010, 10:35 PM
  #2  
Senior Member
Thread Starter
iTrader: (3)
 
chance91's Avatar
 
Join Date: May 2008
Location: Fargo, ND
Posts: 533
Total Cats: 3
Default

k... So nothing yet! I'm going to just figure it out... I assume as long as the length and timings are close, I should be ok. And if they aren't I hope the hydra can fix my mistake. I just think the 550 densos should work better than the 550 rc injectors which are getting to be ancient.
chance91 is offline  
Old 10-17-2010, 12:06 AM
  #3  
Junior Member
iTrader: (6)
 
ogwazza's Avatar
 
Join Date: Aug 2008
Location: New Zealand
Posts: 248
Total Cats: 3
Default

I have been thinking about trying other injectors for a while now. Currently I have 365cc Toyota ones 73mm high, high impedance. And to upgrade to anything else there is a large price difference here in NZ.

I may look into trying the mitsi evo injectors that have the square top.

I wouldn't know tuning advice for you as I run MS so its just changing a few numbers in the settings!
ogwazza is offline  
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
Full_Tilt_Boogie
Build Threads
84
04-12-2021 04:21 PM
StratoBlue1109
Miata parts for sale/trade
21
09-30-2018 01:09 PM
90 Turbo
MEGAsquirt
19
10-19-2015 03:23 PM
Trent
WTB
2
10-01-2015 12:15 PM
The Gleas
MEGAsquirt
3
10-01-2015 09:30 AM



Quick Reply: Injector compatibility, measurements, etc.



All times are GMT -4. The time now is 04:31 PM.