Protecting heater lines from DP
I have done some "googling" and now i have more questions than before. The problem is that my downpipe is in contact with my heater lines. I know that the DP is gonna get hot and melt them. What would be the best (affordable) effective solution to this. I have seen the header "wrap" stuff but not sure if that would keep the heat from melting my lines.
Alloy heat shield was also looking at that but still would like a "professional" opinion. Thanks |
|
Perfect! ordering right now
|
Also you can pry/bend the heater hose as far toward the firewall as possible.
|
Originally Posted by 1redcanuck
(Post 406912)
Also you can pry/bend the heater hose as far toward the firewall as possible.
I still want a heat shield though... |
Shielding is useless if they touch. They must not touch. Then you always need to wrap them.
|
I am using exhaust wrap on my heater lines. One has a thin stainless shield on top of the wrap for abrasion protection since it is in direct contact with the header bung for the EGR. So far so good.
|
Originally Posted by wayne_curr
(Post 406921)
Exactly. I used the top half of my jack handle on the heater pipe and just bent it as far as I could get it. For the wrap I got some reflective fiberglass wrap, prolly exactly like whats in the link above. I didn't click it.
I still want a heat shield though... |
So after deciding to use the jack pump as a lever to use to move the heater lines i slipped and banged the shit out of my elbow. The whole left side of my hand was numb for an hour. Just got back from the ER and i had a contusion. AND i got 2 days off!! Thanks wayne for the sweet idea. I get to finish my exhaust.:laugh::laugh::laugh: With the pain meds they gave me i should be able to
|
wow lol. No idea how you managed that. My jack handle has a huge inner diameter so the heater pipe went inside and there was no way for it to slip off.
Isn't a contusion just a bruise? |
Originally Posted by 1redcanuck
(Post 406905)
and fiberglass weave from wirecare.com. Thats what I did |
This business of bending the heater lines kinda scares me...
I simply cut the hoses which go to the heater core as short as possible, so that they are pulled back away from the downpipe. And they're covered in the same sleeve. Good stuff. Used it on my neighbor's KTM as well, which had a clear PVC hose running right next to the exhaust header. Worked a treat. |
Safety wire can also be used to pull the insulated line away from the DP.
Chris |
Not sure of your geometry, but you might also consider transitioning to beaded hard lines in the vicinity of the downpipe. The hard lines will have a greatly reduced outer diameter for the same inner diameter.
|
I got cheap domestic car alternator heat shielding and cut it to size, then wire wrapped mine. Held up so far.
|
Originally Posted by wayne_curr
(Post 407259)
wow lol. No idea how you managed that. My jack handle has a huge inner diameter so the heater pipe went inside and there was no way for it to slip off.
Isn't a contusion just a bruise? Oh as far as the heat shielding: HSP270200 - Reflect-A-Sleeve Reflective Hose & Wire Covering - 2" I.D X 3' Long - Solid Sewn Seam Part#: HSP270200 Manufacturer Part#: 270200 (Qty: 1 x $22.02) HSP203123 - Colored Sleeving - 25' Roll, Adjustable Inside Diameter:1/4" To 7/16" - Withstands 1200 Degrees F Continuous - Yellow Part#: HSP203123 Manufacturer Part#: 203123 (Qty: 1 x $18.60) HSP350008 - Thermal-Tie Stainless Steel "Zip Ties" - For Fastening Heat Wrap Etc. 8" Long, 8 Pieces Part#: HSP350008 Manufacturer Part#: 350008 (Qty: 1 x $13.96) Heatshield Products - Thermal and heat protective sleeving I have been using this for my cars with no issues at all. Cheers, Prospero |
All times are GMT -4. The time now is 12:14 PM. |
© 2024 MH Sub I, LLC dba Internet Brands