Where do you mount your det cans?
just as the title says. What point on the block do, you who have used det cans, mount the pickup to? Or does this location not matter, just so long as it is mounted to the engine?
thanks, Jared |
Ive always used a bolt on the valve cover when Ive done it on hondas, I havent done it on the miata yet, but Id imagine that it would work all the same.
You can hear quite a lot, i remember doing it once on my buddys car and the sound of the BOV was louder than anything else edit: one of the bolts that hold the engine listing points would probably be good, since theyre directly on the head |
most people i've seen do it bolt it to the motor mounts near the oil pressure sensor and the oil filter.
|
Originally Posted by Full_Tilt_Boogie
(Post 469360)
Ive always used a bolt on the valve cover when Ive done it on hondas, I havent done it on the miata yet, but Id imagine that it would work all the same.
You can hear quite a lot, i remember doing it once on my buddys car and the sound of the BOV was louder than anything else edit: one of the bolts that hold the engine listing points would probably be good, since theyre directly on the head |
I remove the factory knock sensor and screw it in there.
|
Originally Posted by jayc72
(Post 469364)
Wouldn't you just hear valve train noise? I'd think you'd want it to be lower down on the engine.
|
I'd think the oil filter side on the engine mount bolts would be best. The upper most bolt would be just about right in height.
|
I mounted mine in the OEM location which is near the oil filter. Its on every 5 engine and some have knock sensors already there some don't. Mine didn't so I needed to find a bolt setup that worked to mount it. Basically one bolt for the hole the drill and tap that bolt for another bolt to mount the sensor. Took more time to jack the car up than wiring it all up and fit it.
|
Originally Posted by JayL
(Post 469372)
I remove the factory knock sensor and screw it in there.
Which is on the outside of the cylinder walls, on the short block, near the oil filter. My Bosch knock sensor is mounted there = my det can. |
wow, thanks for all the great info! I tried mounting it on the furthest back mounting stud on the intake manifold. So far i only hear valve train noise. So either this is a good thing and i have no detonation, or it is drowned out by the valve noise.
i will try attaching it to the same location as the stock knock sensor. |
Here is a thread on my local MX5 forum which uses a bandpass filter as well as normal knock sensing to help reduce false readings.
Hope we can help you and others DIY Det Cans Band pass filter |
I posted a BP filter for use with the factory sensor and any ECU in the ECU section.
I looked at actual Miata knock waveforms and the knock center frequency was 13 kHz. |
Originally Posted by rrjwilson
(Post 469790)
Here is a thread on my local MX5 forum which uses a bandpass filter as well as normal knock sensing to help reduce false readings.
Hope we can help you and others DIY Det Cans Band pass filter |
Originally Posted by JasonC SBB
(Post 469805)
I posted a BP filter for use with the factory sensor and any ECU in the ECU section.
I looked at actual Miata knock waveforms and the knock center frequency was 13 kHz. |
Originally Posted by buffon01
(Post 469818)
Damn Im stupid. I thought DET CANS, were literally a tube mounted on the block connected to a can for the purpose of listening to whats happening during combustion.
|
Well Hustler you'd like that kit I posted up then. Some use it with a knock sensor some use it with the mic but no-one has shown how the mounted the mic so I cant help there.
|
My det cans consist of the KnockSenseMS supplied knock sensor, a mic input in my laptop, Windows Volume Control and Sennheiser headphones.
|
Originally Posted by Spookyfish
(Post 469927)
My det cans consist of the KnockSenseMS supplied knock sensor, a mic input in my laptop, Windows Volume Control and Sennheiser headphones.
|
jeez, fancy stuff guys. I am just using the tube and headset stethoscope method.
|
Seems like a cheap easy way to keep form blowing your shit up during tuning.
The shop i used to work at had a dyno and we would wear the earmuffs and just lean over near the back of the engine, the earmuffs filter out all the lower pitch stuff and detonation is very clear. This method was not used on anything that we thought could sling pats, either way it was probably horribly unsafe. |
All times are GMT -4. The time now is 09:36 AM. |
© 2024 MH Sub I, LLC dba Internet Brands