Will this turbo work? Im still sketchy on churbos
 

Ok so I have been researching for 2 weeks now on Churbos and yes their pricing allure is strong. I currently run 15psi on a garret but unfortunately caught something wicked in the intake and chewed up the blades pretty bad. . . So I want something to use while I send it off to get repaired. That being said, I keep reading to go with godspeed if i go with a churbo and Bell Engineering seems to get decent power from churbos as well.

I need one that is clocked down for the FM IC piping and IC (single silicone tube setup) to be able to handle 15 psi and still have good spool up.

Any opinions on either of these?

Turbo Charger GT28 GT2870 T04B .60 A/R .63 A/R BMW E30 E36 M3 | eBay


GT2871 GT25 GT28 T25 T28 GT2860 Turbo Turbocharger Turbolader Water Oil .64 A/R | eBay


Any helpful comments would be appreciated. This is going on a 94 M edition already tuned greddy emanage (well tuned at that) 15 psi, 470cc injectors, bigger fp, butterfly brace, tochico/fm springs, 3" exhaust and custom begi downpipe etc.


Thanks!

Jon

youre looking for a 2871 sized turbo, correct?

I should mention i have researched to the point of knowing i need a restrictor: https://www.miataturbo.net/diy-turbo...e-turbo-48563/

but not enough to the point I can make an informed decision.

Wow that was a fast response! lol yeah i currently have an ar .60 t28... it spools to max at 3200 rpm? Id love if it was similar performance but my key requirements are... few to no turbo explosions... and few to no engine explosions as a result of my choice:)

I do think that first link does look like : China charger 2871 BEGi and also is very similar looking to the godspeed model. I also read I should avoid the .84 AR and should stick in the .60-.64 range for what i do.

besides not exploding, why do you want the 2871 size over the 2860 size?

I'd be open to sizing options. I like staying at 280iSh hp where possible but I haven't sized a turbo now in 5+ years so I'm kinda rusty:)

Didn't fm shy away from the 2860?

they shy'd down to the 2560 for the last 10 years?

That's very true.. On the civic sites I looked at, it seemed like after measuring housing etc, churbos trended to be equal to smaller garrets even though they were marketed as larger... I guess that is how I arrived at the 2870 spec.

So you recommend the 2860? (Potato! I still don't know where potatoes came into the name)

so the goal is around 280rwhp on a sotck 1.8L 94 block?

might as ewll save yourself the trouble and shop for rods now.


need to know the goals for the setup. street driving, dyno queen, autox, trackdays?

Mainly street/autocross and maybe a track day a year... A new engine is in the works for next year.

I like to lean smaller for the street, but that's me.

the 2560 is still capable of 280rwhp and will obviously spool faster.

At 15 psi? Ill check it out!!! Thanks! Jon

(Any ar recomendations?)

boost number is arbitrary. it's a measure of how restrictive your IM is.


but i have seen 300rwhp on a 99 block with 14psi with the 2560. keep it mind it was all good components and a real 2560 garrett.

When I ran the calculations a few weeks ago, I started with 12 psi. At 12psi, you are still in the lower half of the efficiency range of the 2860. Unless you are going to keep it when you build your motor, a 2560 should be MORE than enough for street use. Especially on stock rods.

Still looking for an effective 2560 --- but i did find a 2860 GT28 TB28 GT2860 S13 S14 Upgrade Turbocharger turbo fast spool | eBay seems kinda cheap though even for a temp turbo..

mine was $150. :)

that compressor is the exact same one I'm using...but I have a T3 sized turbine.

Just an update- I got another garret gt2860 :)

Almost done the reinstall - ideally be done this weekend!

Thanks again all!

did you buy pauls?