Braineack

iTrader: (62)

just shy of what I thought it would make...all in all I'm very pleased with the torque curve. I need a larger exhaust obviously!


RX7 VS OEM AFM.....

RX7 LOST POWER AT 12PSI!!!!

tabs604

nice one.

I am jeaulous!

magnamx-5

iTrader: (7)

I am dissapointed as well thought you had more comming. Looks pretty damn irch past 6K rpm this could cost ya a few ponys

Al Hounos

So, brain, you didn't say in the other thread, are you going to go MS next year? I'd expect another 20hp.

TheBandit

iTrader: (8)

I too agree there is some power to be had 5700 or so, looks like it got REAL rich. Get it back around 12 or 11.5 and i would imagine 215 or so could be had.
Good job!
-Michael-

Kelly

iTrader: (6)

Nice. Probably woulda hit 250 whp with a full 3"

Braineack

iTrader: (62)

That's what happens when you use the OEM ECU, no way to tune out the top-end AFR.

Yes, I'd expect fairly big gains from a 3.0" over this 2.25".

and yes, this summer I'll tackle MS after I do a new rear.

olderguy

iTrader: (19)

The only way you could tune it out is with an Emanage when using the OEM ECU. MS will, of course do it, and your attempt at reducing fuel pressure at the top end would work; if you could make it happen.

Even with the smaller injectors, my AFR dropped at the top. I could probably pull fuel with the airflow adjustment map, but it would only be to prove the point. I never drive like on the dyno. Who does?

Braineack

iTrader: (62)

Brad's finally making some good power too...however having the same problem keeping the wastegate under control without a helper spring....


Compared to Olderguy's 1st run last summer:

ray_sir_6

iTrader: (1)

What other mods are you running?

brgracer

iTrader: (14)

Good numbers. I'm a bit surprised that the T3 didn't make more power at 12psi even with a 2.5" exhaust. It looks like the torque curve starts dropping off a little earlier than usual, were you holding 12 psi to redline or was the boost dropping a little?

Braineack

iTrader: (62)

boost holds strong to redline

i'm using a 2.25" dual exit catback actually

Braineack

iTrader: (62)

see my VBGarage for a full list of mods....but basically:

T3 S60 Turbo
12x11x18" intercooler
Vortech FMU
Pierburg Pump
O2 clamp
Bipes ACU
BEGi Manifold & DP

m2cupcar

iTrader: (5)

You'd think the rx7 meter would have leaned out that top end some.
Where do you hit 12psi? Your power curve has a nice rise and then flattens with the torque curve- think that's the exhaust?

Braineack

iTrader: (62)

no, my logs show it being the exact same...it's just the nature of the ecu using an internal map and I'm using 305cc injectors.

I hit 12psi at around 4.2k.

I really think the exhaust is a bottle-neck that's limiting my full potential....but seriously...I'm happy with the numbers....

rotaryjunky

iTrader: (3)

I would love that kind of power someday. Congratulations. Nice "baseline".

m2cupcar

iTrader: (5)

Just follow the FAQs

Ben

iTrader: (33)

I have torque envy. All of you (OG, NBS, B) have sick torque curves.



Braineack, can you repost a graph starting at 1k rpm? Thx

Braineack

iTrader: (62)

no can do....I start to run at 3k, some a little later...had to slam on the gas, start my datalog and hit the dyno button all at once...

Ben

iTrader: (33)

All good.

They let you run the dyno? :gay: