I have a front end now!!!
1 Attachment(s)
Finally I feel like I'm making progress... Got the nose put back on and some other tidbits. Finish fab'ing some heatsheilds for the turbo and the hood can go on. Next step is the interior, fab a center console, seats, etc. Still need to find a headlight cover that is vented to feed the airbox.
So far: rebuilt the engine with Wiseco pistons and ETD rods six speed tranny with 6spd starter and plate rebuilt rear with 3.6 gears AEM wideband o2 Mishimoto radiator with slim fans door bars frame rails fuel rail new downpipe carbontrix extraction vent on hood ACT Pro 9lb flywheel, pressure plate and clutch new clutch slave and braided line that replaces that curly q thing added a oil temp gauge all new hoses, vacuum lines, belts, seals, everything cleaned up all wiring harnesses and wrapped replaced power steering with a new manual rack new balljoints, tie rod ends, poly bushings throughout new pads on the Wilwoods new coil, plugs, wires Vary splitter I'm glad I didn't keep receipts, the total $$ is pretty scary.... |
should have depowered your power steering rack, it has a higher ratio in it I believe. Post some pictures of the hood.
|
lookin good man, keep up the good work.
__________________ Best Car Insurance | Auto Protection Today | FREE Trade-In Quote |
Great job man, I envy you, that's pretty much the list of things that my car is supposed to have by now...but I fail!
Keep up the great work, your car is something to be proud of. |
did you paint your intercooler pipes or have them powder coated?
|
Originally Posted by shaddbarr
(Post 367737)
did you paint your intercooler pipes or have them powder coated?
|
Originally Posted by mazda/nissan
(Post 367749)
I think they are FM's silicone IC lines
|
Originally Posted by akaryrye
(Post 367906)
Nah, thats an older FM/begi kit. Metal pipes powdercoated red
|
Very clean setup! I love that Garage Vary splitter...just wish they didn't cost so damn much.
I have a quick question for ya...I'll be running a FM2 intercooler/piping setup like yours, but I've got a cxracing/godspeed/mishimoto rad with the stock fans. I'm gonna have to buy slim fans to get that piping to fit, aren't I? |
Originally Posted by messiahx
(Post 368126)
Very clean setup! I love that Garage Vary splitter...just wish they didn't cost so damn much.
I have a quick question for ya...I'll be running a FM2 intercooler/piping setup like yours, but I've got a cxracing/godspeed/mishimoto rad with the stock fans. I'm gonna have to buy slim fans to get that piping to fit, aren't I? |
Originally Posted by thymer
(Post 367418)
I'm glad I didn't keep receipts, the total $$ is pretty scary....
Nice build. That should be a great ride. |
[QUOTE=mazda/nissan;367425]should have depowered your power steering rack[QUOTE]
+1 Everything else is lookin' good kiddo. |
Good to see someone else running a color-matched GV lip. How was the 6 speed swap?
|
Originally Posted by kotomile
(Post 369101)
Good to see someone else running a color-matched GV lip. How was the 6 speed swap?
|
How can you make a list of all that shit and only post one pic?
|
Originally Posted by patsmx5
(Post 369197)
How can you make a list of all that shit and only post one pic?
|
OK, here's some pics
7 Attachment(s)
Got the extractor vent installed on the hood. Still need to fab heat shields around turbo and finish air box. I didn't like the huge gap around the intake pipe at the air filter box so cut some rubber out and riveted it in. Flexes with the engine but keeps a nice seal. I have a vented headlight cover on order to feed it. I lowered the steering a bit and will be fabbing a center console out of aluminum and black carpet. Going to try guncote on the aluminum center console. I use it to refinish rifles and it's really tough, heat resistant, etc. You sandblast, airbrush it on, and then bake it in the over. I'm also going to move the link down lower under the radio. Like that fancy fuel line brace? Only took two tries to get it right! :) If you notice the inspection sticker you can see it's been off the road for some time....
|
I like the rubber. I plan on doing something to fix the cold air box this spring because that huge gap around the pipe seems like it must effect its performance.
|
Such a nicely built car and Link engine management? Maybe you should use a commodore 64 to run it :)
|
Originally Posted by Newbsauce
(Post 369351)
Such a nicely built car and Link engine management? Maybe you should use a commodore 64 to run it :)
|
All times are GMT -4. The time now is 01:58 AM. |
© 2024 MH Sub I, LLC dba Internet Brands