- Engine Performance (https://www.miataturbo.net/engine-performance-56/)

- - Seals and Gaskets for a VVT motor build (https://www.miataturbo.net/engine-performance-56/seals-gaskets-vvt-motor-build-91920/)

Seals and Gaskets for a VVT motor build

Spent some time over in my thread compiling stuff. Feel free to add on. This order came out to around $100 on mazdacomp

Dipstick O-ring: 9954-10-0907
Front Oil pan Seal: B541-10-427
Rear Oil pan Seal: B541-10-428
Front Main Seal: B3C7-10-602A (already have)
Rear Main Seal: BP05-11-312
Oil Pump pickup gasket: B6BF-14-248

Valve cover gasket: BP6D-10-235A
Intake mani to head: BP4W-13-111
Intake mani upper to lower: BP5A-13-135

VVT cover gasket thing under the plate with 3 screws: ZL09-10-607
3 VVT screws: 9YAF-00-501
Intake cam seal: ZL09-10-602 (Included in VVT rebuild)
Exhaust cam seal: FS05-10-602A

E301-15-287 mixing manifold O-ring. I think the MM to water pump gasket comes with a new WP. The MM O-ring sometimes needs to get replaced on its own tho.

8DN5-10-271 GASKET SET,ENGINE 1.00 $222.20
Easy mode.

Metal Gasket under VVT valve body and under 3-bolt plate also come with the rebuild kit.

The gasket under the 3 bolt plate isn't shown in the kit picture. I'll see what happens when it shows up.

EGR gaskets on intake manifold

JE27-20-305A
JE06-20-306

Woodruff Key:

B3C7-11-317

PCV grommet:

E301-13-338A

Thermostat Water Pipe Neck O Ring 90 thru 05

B61P-15-106A

The Miata Roadster VVT kit doesn't come with two copper crush washers for oil line to block: 99562-1000

did we ever confirm that the 3-hole VVT cam bolt gasket thingy comes with the miataroadster kit?

https://cimg5.ibsrv.net/gimg/www.mia...2dfffa4ccb.png

This seal came in the VVT rebuild kit

i wish this list was here when i bought all that stuff.

I bought almost every seal new in late 2015 for a build I am doing. This is what I have:

Dipstick O-ring: 9954-10-0906
Water pump gasket: B6BF-15-116
Water pump inlet gasket: B366-15-165
Intake Manifold Gasket: BP4W-13-111
Front oil pan gasket: B541-10-427
Rear oil pan gasket: B541-10-428
Head gasket: BP26-10-271 (This gasket is the one for the earlier 1.8 blocks, not the NB2 blocks still works though)
Valve cover gasket: BP6D-10-235A
Exhaust Manifold Gasket: BPD3-13-460
Oil pickup tube/strainer gasket: B6BF-14-248
PCV valve grommet: E301-13-338A
Woodruff Key: B3C7-11-317
Rear main crank seal: BP05-11-312
Front crank seal: B3C7-10-602A
Exhaust Cam Oil seal: FS05-10-602A (I think)
Throttle body gasket: B6BF-13-655
Upper banjo bolt crush washer for VVT line on block (VVT): ZL09-10-333 (need 2 of these)
Lower timing cover gasket: B660-10-522
Middle timing cover gasket: B660-10-673
Oil control case adapter O ring (VVT): BP6D-10-673 (need 2 of these)
Freeze plugs (1-1/4" O.D.): 9930-63-000 (I think you need 7 of these)
Camshaft position sensor: ZJ10-18-221
Oil pump O ring: FE1H-14-122B
Intake cam oil seal: ZL09-10-607
Front VVT cover 3 bolt gasket (VVT): ZL09-10-607
Timing cover plate U-shaped rubber seal: B61P-10-544
Tension pulley: GMB455-2050 (Not mazda part #)
Idler pulley: GMB445-2060 (Not mazda part#)
upper horizontal water pump seal: B660-10-543B
STD thrust washer/bearing: ZJY1-10-SJ0
Oil pipe o ring (VVT): 9954-10-2206 (need 1 of these)
Freeze plugs ( 1-3/8" O.D.): 9930-63-500 (I think you need 2 of these)
JDM/EUDM Squaretop Intake manifold plenum: BP6Z-13-135
VVT O ring (VVT): ZL09-10-674 (need 2 of these)
Lower Banjo bolt crush washer for VVT line on block (VVT): 9956-21-000 (need 2 of these)
IAC valve gasket: BP2Y-13-W89
Cap at the back of cylinder head Exhaust cam side: KLG4-12-603
VVT body gasket (VVT): BP6D-10-663
VVT oil filter (VVT): ZL09-14-3X2
VVT torx screws (VVT): 9YAF-00-501 (need 3 of these)
Tensioner spring: B660-12-711C
Competition Engine mounts: NAY1-39-040 (need 2 of these)
Oil galley plug: 0221-10-327 (not sure if 1 or 2 are needed)

I'm pretty sure the entire gasket kit is way cheaper. And includes valve stem seals. I'm not sure what all is included though.

Quote:

Originally Posted by aidandj (Post 1410360)

I'm pretty sure the entire gasket kit is way cheaper. And includes valve stem seals. I'm not sure what all is included though.

Yeah you're probably right, but I couldn't find anywhere online where it said what parts were included in the kit. I also wanted a few different parts like the earlier style 1.8 head gasket instead of the newer one so I pieced it out myself. Took me a while to collect this info. Hopefully it's helpful to someone else.

if I google mazdacomp all I get is a page that won't load and hasn't loaded since I first saw the thread. Any link to a good source for that gasket kit is greatly appreciated since the Icelandic mazda dealership wants a stupid amount of money for it.

Quote:

Originally Posted by G3ML1NGZ (Post 1410393)

Priority Mazda is where I go for all my OEM parts. I have been buying parts from Tommy for over 10 years now and he has always been great.

Thermostat Water Pipe Neck O Ring 90 thru 05 B61P-15-106A

Thermostat Water Pipe Neck O Ring 90 thru 05

B61P-15-106A