Skunk2 vs Square/Flat Top Intake Manifold - Dyno Results

Reply Subscribe

Thread Tools

Search this Thread

12-23-2017, 10:23 AM

#21

Zsanz

Junior Member

Join Date: Mar 2017

Location: Derpsville

Posts: 163

Total Cats: -11

Awesome.
The helpdesk ticket I had in to that mentioned Eric Gonz guy in the junk2 thread was answered that the plenum spacer was only needed if you're pushing 400hp, interesting that they could provide this data point but no granular data. This forum rocks.

12-23-2017, 11:10 AM

#22

curly

Cpt. Slow

iTrader: (25)

Join Date: Oct 2005

Location: Oregon City, OR

Posts: 14,184

Total Cats: 1,135

If you want midrange, go with a vics or even vtcs manifold.

12-23-2017, 12:14 PM

#23

Stealth97

Elite Member

iTrader: (5)

Join Date: Oct 2007

Location: Canton, Ga

Posts: 2,156

Total Cats: 66

Quote:

Originally Posted by curly

If you want midrange, go with a vics or even vtcs manifold.

I have a VICS. The build quality is just so awful.. that turn behind the throttle body has got to be sucking Power. I will at least go flat top.. looking at low end for the skunk I doubt I’d have enough power at low RPM to spin the A/C Compressor

-5

12-23-2017, 02:49 PM

#24

18psi

VladiTuned

iTrader: (76)

Join Date: Apr 2008

Posts: 35,821

Total Cats: 3,481

Those are some really stupid assumptions to make.

12-23-2017, 07:52 PM

#25

Stealth97

Elite Member

iTrader: (5)

Join Date: Oct 2007

Location: Canton, Ga

Posts: 2,156

Total Cats: 66

Quote:

Originally Posted by 18psi

Those are some really stupid assumptions to make.

Cats for you sir

12-25-2017, 03:39 AM

#26

mx5psi

Junior Member

Join Date: Mar 2013

Posts: 209

Total Cats: 35

i need some help i currently have a BEGI inlet manifold and am considering if it would it be worth me swapping to a SKUNK2 unit as iam not really happy with the ford TB they use and i have had to repair it already when it split along the top on a weld.

my only draw back to replacing my current one the BEGI one is match ported i had it rewelded and reported it myself BEGI had it miles off and its currently working fine.

Last edited by mx5psi; 12-25-2017 at 03:51 AM.

12-25-2017, 06:47 AM

#27

Full_Tilt_Boogie

Elite Member

iTrader: (1)

Join Date: May 2009

Location: Jacksonville, FL

Posts: 5,155

Total Cats: 406

Quote:

Originally Posted by mx5psi

How high do you rev your setup?

I would definitely unload the BEGi on someone who doesnt know any better. Im sure it would still sell for a bit used.

12-25-2017, 08:08 AM

#28

mx5psi

Junior Member

Join Date: Mar 2013

Posts: 209

Total Cats: 35

Quote:

Originally Posted by Full_Tilt_Boogie

How high do you rev your setup?

I would definitely unload the BEGi on someone who doesnt know any better. Im sure it would still sell for a bit used.

7800rpm if i remember right the car works well at the moment but i bought the begi one 3 years ago for the lack of a better choice seems like i have choices now.

12-25-2017, 09:59 AM

#29

Mazdaspeeder

Senior Member

Join Date: Feb 2009

Location: Philadelphia

Posts: 916

Total Cats: 70

BEGi lol

12-25-2017, 03:56 PM

#30

ky-sephia

Junior Member

Join Date: Oct 2011

Location: Louisville

Posts: 60

Total Cats: 3

Quote:

Originally Posted by mx5psi

7800rpm if i remember right the car works well at the moment but i bought the begi one 3 years ago for the lack of a better choice seems like i have choices now.

I would buy the S2, put it aside and when the Begi breaks again then swap them out. The S2 will work better and will accommodate your RPM needs.