5000 RPM's at start!?
#1
Junior Member
Thread Starter
iTrader: (1)
Join Date: Aug 2011
Location: Queens, NYC
Posts: 150
Total Cats: 6
5000 RPM's at start!?
I vent a boosted 99 motor a little over a month ago (https://www.miataturbo.net/engine-pe...der-1-a-68618/) and now I have a new motor and other goodies all ready to go. I have a MS2 PNP from Stratified Auto. I adjusted for the larger injectors and calibrated everything. I believe everything is connected correctly. EGR delete. Innovative Mtx-l.
When I went to start it for the first time, it fired after about 3 attempts.
The problem is that the motor revs up to 5k right away without any input to the throttle. It's like I am flooring it before I turn the key. I turn it off asap. It's not the TB cable. I disconnected it and checked the plate. All is well.
I saw a little bit of smoke coming from around the intake manifold closer to the firewall a couple of times. One of my friends said he thought he saw a spark coming from the area around the #4 injector. We switched places and I didnt see anything.
I dont think it's a vacuum leak because all of the holes are accounted for.
Please help.
Thanks. Sorry if I left out any vital info out.
When I went to start it for the first time, it fired after about 3 attempts.
The problem is that the motor revs up to 5k right away without any input to the throttle. It's like I am flooring it before I turn the key. I turn it off asap. It's not the TB cable. I disconnected it and checked the plate. All is well.
I saw a little bit of smoke coming from around the intake manifold closer to the firewall a couple of times. One of my friends said he thought he saw a spark coming from the area around the #4 injector. We switched places and I didnt see anything.
I dont think it's a vacuum leak because all of the holes are accounted for.
Please help.
Thanks. Sorry if I left out any vital info out.
#2
Boost Pope
iTrader: (8)
Join Date: Sep 2005
Location: Chicago. (The less-murder part.)
Posts: 33,026
Total Cats: 6,592
There are three ways for air to get into the engine:
1: Past the throttle plate.
2: Through the idle valve
3: Through the gaping vacuum leak.
If the throttle is closed, then it's #2 or #3. I don't think the IAC valve can flow enough air to achieve 5,000 RPM, even with no load.
So that leaves the vacuum leak. Brake booster hose? Manifold? EGR valve? Not a whole lot of places to look, really.
1: Past the throttle plate.
2: Through the idle valve
3: Through the gaping vacuum leak.
If the throttle is closed, then it's #2 or #3. I don't think the IAC valve can flow enough air to achieve 5,000 RPM, even with no load.
So that leaves the vacuum leak. Brake booster hose? Manifold? EGR valve? Not a whole lot of places to look, really.
#3
Junior Member
Thread Starter
iTrader: (1)
Join Date: Aug 2011
Location: Queens, NYC
Posts: 150
Total Cats: 6
In fact the IAC hose is sorta kinked so if anything there is a lack of air flow.
I checked everything that I think there is to check as far as vacuum. Ill keep looking and make sure everything is sealed. Is there anyway I can screw up the vacuum hoses around the manifold that will cause this?
Also, I didnt put any sealant or anything on the EGR delete plates but used the metal gasket where the solenoid was. Could that be a potential problem?
Thanks
I checked everything that I think there is to check as far as vacuum. Ill keep looking and make sure everything is sealed. Is there anyway I can screw up the vacuum hoses around the manifold that will cause this?
Also, I didnt put any sealant or anything on the EGR delete plates but used the metal gasket where the solenoid was. Could that be a potential problem?
Thanks
#12
Junior Member
Thread Starter
iTrader: (1)
Join Date: Aug 2011
Location: Queens, NYC
Posts: 150
Total Cats: 6
Ahh ok. Thanks.
I do have a spare TB with IAC which I can swap with and see what happens too.
EDIT: Back story: The reason I have a spare TB is because while setting up the MS before the first start with the last motor, the IAC started buzzing very loud. It didnt do it all the time and it stopped when I unplugged it. I thought is was bad so I got another one. This one does the same now whenever I am click Burn/change a setting in TunerStudio. It doesn't buzz when I am trying to start the car.
I do have a spare TB with IAC which I can swap with and see what happens too.
EDIT: Back story: The reason I have a spare TB is because while setting up the MS before the first start with the last motor, the IAC started buzzing very loud. It didnt do it all the time and it stopped when I unplugged it. I thought is was bad so I got another one. This one does the same now whenever I am click Burn/change a setting in TunerStudio. It doesn't buzz when I am trying to start the car.
Last edited by Kinavo; 12-02-2012 at 09:43 AM.
#14
Junior Member
Thread Starter
iTrader: (1)
Join Date: Aug 2011
Location: Queens, NYC
Posts: 150
Total Cats: 6
I changed the TB. I sealed the EGR plates. I triple checked every vacuum hose/plug and removed the kink from the hose going into the IAC.
Same thing happens.
Here is my current tune.
Also a log with IAC unplugged and the last one is with the IAC plugged at start. They are very short since I am afraid to leave it running at those rpm's.
Thanks guys.
Same thing happens.
Here is my current tune.
Also a log with IAC unplugged and the last one is with the IAC plugged at start. They are very short since I am afraid to leave it running at those rpm's.
Thanks guys.
Last edited by Kinavo; 12-02-2012 at 03:00 PM.
#15
Boost Pope
iTrader: (8)
Join Date: Sep 2005
Location: Chicago. (The less-murder part.)
Posts: 33,026
Total Cats: 6,592
Air is getting into the system somewhere.
If you still suspect the IAC valve, pull the hose and block it off. Simple test.
Did that fix it? If not, it's somewhere else.
Maybe the two halves of the intake manifold aren't sealed. Maybe it's the throttle body. Maybe something got between the intake manifold and the head. Maybe the brake booster hose (or some other vacuum hose) is the culprit. Maybe the PCV valve is completely open.
This is going to be some basic gumshoe work.
If you still suspect the IAC valve, pull the hose and block it off. Simple test.
Did that fix it? If not, it's somewhere else.
Maybe the two halves of the intake manifold aren't sealed. Maybe it's the throttle body. Maybe something got between the intake manifold and the head. Maybe the brake booster hose (or some other vacuum hose) is the culprit. Maybe the PCV valve is completely open.
This is going to be some basic gumshoe work.
#16
Elite Member
iTrader: (2)
Join Date: May 2007
Location: Cromwell, Connecticut
Posts: 2,604
Total Cats: 16
Did you use the correct IM gasket to the head?
I started up my brand new motor (with 96 head) with a 99 gasket on it and it was a MAJOR leak. motor sat at 4k. . . epic fail.
I feel your pain, its tough to find the leak because you dont want a brand new motor sitting at 4-5k while you feel around for a leak.
I started up my brand new motor (with 96 head) with a 99 gasket on it and it was a MAJOR leak. motor sat at 4k. . . epic fail.
I feel your pain, its tough to find the leak because you dont want a brand new motor sitting at 4-5k while you feel around for a leak.
#17
Junior Member
Thread Starter
iTrader: (1)
Join Date: Aug 2011
Location: Queens, NYC
Posts: 150
Total Cats: 6
I will have to do the IAC vavle test with both of them. I know the TB is okay. Its closed and the spring works fine and plate looks good.
I checked the brake booster line. It's okay.
The 6 bolts for the top half of the IM are torque and with the metal gasket in between. Anyone use gasket sealer there?
How do I test the PCV valve?
I forgot to mention that I am using the Hondata IM gasket. I torqued all of the nuts to spec. The engine was out when I did all of this so I had a good view of all the surfaces and whatnot and all looked well. Is there any way to test this without taking the entire IM off and the engine off or briefly on?
Is there any way to slow the engine down using the MS despite the additional air getting in?
I checked the brake booster line. It's okay.
The 6 bolts for the top half of the IM are torque and with the metal gasket in between. Anyone use gasket sealer there?
How do I test the PCV valve?
I forgot to mention that I am using the Hondata IM gasket. I torqued all of the nuts to spec. The engine was out when I did all of this so I had a good view of all the surfaces and whatnot and all looked well. Is there any way to test this without taking the entire IM off and the engine off or briefly on?
Is there any way to slow the engine down using the MS despite the additional air getting in?
#18
If you have a "leak down tester" try the following:
- with the engine switched off...
- Turn over the crank until one cylinder is at bottom dead centre and the intake valves are just about to close (I.e. At the end of the intake stroke)
- insert the leak down tester into that sparkplug hole and pressurise the line to 20 psi or so (you should not need much, 100 psi for example may start damaging unrelated stuff like the PCV)
- listen carefully, you should be able to hear air escaping out the same place it's leaking in when running...
Good luck...
- with the engine switched off...
- Turn over the crank until one cylinder is at bottom dead centre and the intake valves are just about to close (I.e. At the end of the intake stroke)
- insert the leak down tester into that sparkplug hole and pressurise the line to 20 psi or so (you should not need much, 100 psi for example may start damaging unrelated stuff like the PCV)
- listen carefully, you should be able to hear air escaping out the same place it's leaking in when running...
Good luck...
#19
There are two holes in the back of the intake manifold(94-97 for certain) from EGR. Make sure the correct one is covered.
I've heard of air getting past the seal on the throttle shaft pivot points. If you've clean the plate you can clean the seal off the outside edge too. That will cause problems too, not to that high of a rev but it could add up.
I've heard of air getting past the seal on the throttle shaft pivot points. If you've clean the plate you can clean the seal off the outside edge too. That will cause problems too, not to that high of a rev but it could add up.
#20
Elite Member
iTrader: (2)
Join Date: May 2008
Location: Portland, Oregon
Posts: 3,468
Total Cats: 365
Re-check the torque on the intake manifold bolts, IMO. I haven't heard of anyone using gasket sealer there and the FSM does not indicate it should be used.
And triple-check all of the little vent fittings. There's on low on the side of my throttle body that I've missed before.
Also, double check that the TB itself is torqued down properly.
You have a leak somewhere, it has to be either a fitting with no hose attached, a leaking hose, or something's not torqued down properly and it's leaking around the gasket. 5k rpm is quite a bit of air. Check everything methodically and you'll find it.
And triple-check all of the little vent fittings. There's on low on the side of my throttle body that I've missed before.
Also, double check that the TB itself is torqued down properly.
You have a leak somewhere, it has to be either a fitting with no hose attached, a leaking hose, or something's not torqued down properly and it's leaking around the gasket. 5k rpm is quite a bit of air. Check everything methodically and you'll find it.