99 Are these pnp injectors? Custom Fiveo 026IMP750X
#1
Elite Member
Thread Starter
iTrader: (7)
Join Date: May 2007
Location: Dallas, Tx
Posts: 3,006
Total Cats: 103
99 Are these pnp injectors? Custom Fiveo 026IMP750X
http://www.fiveomotorsport.com/produ.../?p=026IMP750X
first ones on page, 550cc for a 99
first ones on page, 550cc for a 99
Will fit stock fuel rail/intake/electrical connection.
You are puchasing an exclusive set of brand new and flow matched EV14 550cc fuel injectors for modified engines.
Priced right, at $75 each for superstreet and racing applications.
FLOW CHART: Each set is sold with a complete flow-data chart indicating individual dynamic and static flow rates at 3, 3.5, and 4 BAR at 25%, 50% and 100% for each injector, along with dead time (latency) at 14 volts.
Flow matching was done with industry-standard equipment of the highest quality. The test was performed at varying temperatures to achieve realistic results.
No adapters, No wiring issues, no soldering.
Bosch fuel injectors - flow-matched, high performance fuel injectors.
Use with stock rail, stock electrical harness, and stock intake - with highly modified engine four, six cylinder
Manufacturer flow rates do vary slightly from set to set.
You get a custom flow matched set that will not vary more than 1% or less than 10cc across the set.
But the most important statistic is the pulsed-flow rate on this set of injectors is nearly perfect.
Injector type: EV14-Long, saturated
Dimensions:
Oring to Oring: 64mm
Overall length: 75mm
Electrcial connector: Sumitomo (Denso)
550cc/min at 43.5 PSI (3 BAR)
600cc/min at 50 PSI (3.5 BAR)
660cc/min at 58 PSI (4 BAR)
Latency (Dead Time): 0.65ms at 14 volts
Tested Resistance: 12.5 Ohms
Voltage: 8-15 Volts, Nominal 13.5 Volts
Amperage: 1.0 Amps
Pressure: Min. 36 PSI (2.5 bar), Max. 130 PSI (9 bar)
Excellent fuel atomization - Excellent linearity
Low end pulse width accurate to within 1% down to 2ms.
This injector will not require more than 1% trim
You are puchasing an exclusive set of brand new and flow matched EV14 550cc fuel injectors for modified engines.
Priced right, at $75 each for superstreet and racing applications.
FLOW CHART: Each set is sold with a complete flow-data chart indicating individual dynamic and static flow rates at 3, 3.5, and 4 BAR at 25%, 50% and 100% for each injector, along with dead time (latency) at 14 volts.
Flow matching was done with industry-standard equipment of the highest quality. The test was performed at varying temperatures to achieve realistic results.
No adapters, No wiring issues, no soldering.
Bosch fuel injectors - flow-matched, high performance fuel injectors.
Use with stock rail, stock electrical harness, and stock intake - with highly modified engine four, six cylinder
Manufacturer flow rates do vary slightly from set to set.
You get a custom flow matched set that will not vary more than 1% or less than 10cc across the set.
But the most important statistic is the pulsed-flow rate on this set of injectors is nearly perfect.
Injector type: EV14-Long, saturated
Dimensions:
Oring to Oring: 64mm
Overall length: 75mm
Electrcial connector: Sumitomo (Denso)
550cc/min at 43.5 PSI (3 BAR)
600cc/min at 50 PSI (3.5 BAR)
660cc/min at 58 PSI (4 BAR)
Latency (Dead Time): 0.65ms at 14 volts
Tested Resistance: 12.5 Ohms
Voltage: 8-15 Volts, Nominal 13.5 Volts
Amperage: 1.0 Amps
Pressure: Min. 36 PSI (2.5 bar), Max. 130 PSI (9 bar)
Excellent fuel atomization - Excellent linearity
Low end pulse width accurate to within 1% down to 2ms.
This injector will not require more than 1% trim
Thread
Thread Starter
Forum
Replies
Last Post