Larimer

iTrader: (4)

I picked up some Corbeau Forza II's (I believe they're the II's, they look like these: Corbeau: Forza ) but they don't fit in the car it seems. I'm debating getting other seats or just beating on the trans tunnel to make them fit. It seems that other people have got them to fit, but most used sliders. I'm bolting mine to the floor to get the headroom I need. Should I beat on the tunnel of my 94 R or just put them on craigslist and try and get narrower seats? The only reason I bought them was because they were $300 for the pair and they were only 2 months old.

Hi Im Simon

iTrader: (18)

beat the tranny tunnel i did the same.

ctdrftna

iTrader: (1)

or make custom mounts and shift the seat a little, my car is full out race, so im have a sparco circut pro, its deff should not fit, but we welded custom mounts to the floor, to sit the seat as low as possible and to make it fit

Mach929

iTrader: (3)

just beat it

Larimer

iTrader: (4)

I figured I'd get that response. It just seems that I would need quite a bit of room to get it to fit. I'd also need to do the same on the passenger side so I'll have to see how much room I have before getting too close the trans./driveshaft/PPF.

Larimer

iTrader: (4)

Looking at the seat dimensions yours looks like it would fit much better. The width is 17.5" at the base and the Forza is 20.5".

miataspeed2005

iTrader: (3)

Beat it, that's what I did for my sparco pro2000's

gospeed81

iTrader: (51)

I had to do the same thing.

Actually, I reshaped the tranny tunnel and bent my Sparco brackets.


EDIT:

Honestly...to answer your question...I'd consider getting another seat IF you are DDing it. Unless the II is tons more comfortable you'll hate it.

Larimer

iTrader: (4)

Not a DD, just a track/nice day car.

gospeed81

iTrader: (51)

In that case you'll love it...

I had to stretch some of that material pretty thin while beating on it....but it's held up to about 8K miles.

Larimer

iTrader: (4)

What seats did you put in? Everybody who says they've done this has much narrower seats and I'm worried I'll really have to abuse the tunnel to get them in there. Kind of the opposite scenario to a hot dog in a hallway.

curly

iTrader: (25)

Targa Miata

Pretty sure Keith beat it. Maybe not though, slightly different seat.

Larimer

iTrader: (4)

Yeah that's an older Forza that they used for test fitting. Supposedly the Forza II is wider but I can't find any comparison between the two.

gospeed81

iTrader: (51)

Mine's the original Forza. It's still a wide beast. I had the most hell getting the shoulders to clear the door card with the seat as far forward as I needed it. I tried 3 times before I got position, incline and angle (relative to longitudinal axis of car) all right.

Larimer

iTrader: (4)

I just don't want to beat the hell out of it and then have it not still fit. Call me a *****, but I hate finding things out the hard way. I might take the cover off the seat and see if there's any way to make it a bit slimmer rather than beating on the car just yet.

Larimer

iTrader: (4)

****. I just measured the seats and checked the dimensions online and I have the wide version. No wonder they don't fit at all. I didn't even think to measure them when I was buying them off the guy. Back to craigslist they go.

pusha

iTrader: (5)

Where are you located? I may be interested.

Larimer

iTrader: (4)

Cincinnati.

http://cincinnati.craigslist.org/pts/1517839060.html