hmm high vaccum @ idle
03-27-2008, 07:12 PM
#1
Junior Member
Thread Starter
iTrader: (1)
Join Date: Jun 2005
Location: San Jose
Posts: 213
Total Cats: 0
hmm high vaccum @ idle
So I was searching around old threads and I saw one about vacuum @ idle. I thought my vacuum was normal ( - 11-12psi) but I see that most people have - 18-22. My AFPR looks ok and my idle is around 1K. My fuel pressure idles @ 43 psi (I'm not using a AFPR) but I thought that might be because I'm using a 190lp HP pump. Injectors are new and so are the O-rings. So...
Where are good places to look for leaks?
What's the best method to find them?
Thanks,
t.t.
Where are good places to look for leaks?
What's the best method to find them?
Thanks,
t.t.
Reply
0
0
03-27-2008, 07:43 PM
#4
Junior Member
Thread Starter
iTrader: (1)
Join Date: Jun 2005
Location: San Jose
Posts: 213
Total Cats: 0
hmm ok I was wrong I guess. I thought my Prosport read everything in PSI but I guess if it's vacuum it reads inhg instead.
This is what I'm using.
http://prosportgauges.com/Digital-boost-1.aspx
so 10-11 inhg = vacuum leak?
This is what I'm using.
http://prosportgauges.com/Digital-boost-1.aspx
so 10-11 inhg = vacuum leak?
Reply
0
0
03-27-2008, 07:56 PM
#7
I'm not converting units, but IF you do have a vacuum leak, I would first look to the last are you messed with. So, if you dropped in new injectors yesterday, I might start there. You can spray carburetor cleaner where you suspect there is a leak. If there is, engine speed will change, the engine will respond, making it obvious.
Reply
0
0
03-27-2008, 08:47 PM
#10
Low vacuum is not absolutely a leak.
What is your ignition timing doing and is the cam timing correct? Poor engine condition (ie compression) can lower vacuum as well. Poor A/F ratio can also make it take a dump.
To drop 6-7" of vacuum you wouldn't have to search real hard for a leak, it would be a very loud leak.
HTH
Ron
What is your ignition timing doing and is the cam timing correct? Poor engine condition (ie compression) can lower vacuum as well. Poor A/F ratio can also make it take a dump.
To drop 6-7" of vacuum you wouldn't have to search real hard for a leak, it would be a very loud leak.
HTH
Ron
Reply
0
0
03-27-2008, 08:59 PM
#11
Junior Member
Join Date: Mar 2008
Location: Charleston, S.C.
Posts: 159
Total Cats: 0
Did it drop after you installed the new injectors?? A bad seal at the injector could be the culprit. I use an unlit propane torch to search for leaks. Wanding it around the places a leak could occur will allow the fuel to pull in and raise the idle when you find the leak.
Reply
0
0
03-27-2008, 10:51 PM
#15
Junior Member
Thread Starter
iTrader: (1)
Join Date: Jun 2005
Location: San Jose
Posts: 213
Total Cats: 0
chriscar:
unfortunately even if I had that I don't have anything to hook it up to :|
04_Miata:
it's the same reading before the injectors.
Alta Racer:
I'll need to dig up my timing gun but last I check it was 10 at idle
Braineck:
it's 10 in/hg not psi, my mistake
Matt: yeah I realize now that it only goes to 14inHg(actually it goes to 15) but even so I'm getting 10-11 so there's something wrong there.
jtothawhat:
my bov is recirculating, would the spring still matter?
unfortunately even if I had that I don't have anything to hook it up to :|
04_Miata:
it's the same reading before the injectors.
Alta Racer:
I'll need to dig up my timing gun but last I check it was 10 at idle
Braineck:
it's 10 in/hg not psi, my mistake
Matt: yeah I realize now that it only goes to 14inHg(actually it goes to 15) but even so I'm getting 10-11 so there's something wrong there.
jtothawhat:
my bov is recirculating, would the spring still matter?
Reply
0
0
03-28-2008, 06:19 PM
#16
Spring pressure does matter, the stiffer the spring the lower the number ect -20IN/HG with a 11 psi spring vs. -10IN/HG with a 6 psi spring. It allows air to escape at idle. I have a really soft spring in my Tial BOV and at idle I have -10INHG at idle, which most would say is really high, but it's all due to my BOV spring. I would check the spring tension on your Bypass Valve, and if you can tighten it an see if that corrects your problem.
Reply
0
0
03-28-2008, 07:30 PM
#20
Boost Pope
iTrader: (8)
Join Date: Sep 2005
Location: Chicago. (The less-murder part.)
Posts: 33,026
Total Cats: 6,592
Uhm... yeah. You can remove the BOV entirely, leaving a large gaping hole in your intake plumbing, and manifold vacuum will be affected not one little bit. Trust me, mine fell off (well, it was blown off) a few weeks ago. 
Manifold vacuum is all about the space between the exhaust valves and the throttle body, inclusive. If your rings or valves are shot, you'll have low vacuum. If you've got a leak somewhere on the throttle body or the intake manifold, you'll also have low vacuum (and high idle.)
If you do have any appreciable vacuum in the intake tract between the air inlet and the throttle body (where the BOV lives) then you really need to clean your air filter.
Manifold vacuum is all about the space between the exhaust valves and the throttle body, inclusive. If your rings or valves are shot, you'll have low vacuum. If you've got a leak somewhere on the throttle body or the intake manifold, you'll also have low vacuum (and high idle.)
If you do have any appreciable vacuum in the intake tract between the air inlet and the throttle body (where the BOV lives) then you really need to clean your air filter.
Reply
0
0
