anything I need to know before I do my clutch today?
Should I go buy some impact extensions and an impact swivel...or can I use ar powered varieties?
What size impacts to I need for the bell housing and other stuffs, that are > 19mm? thanks |
I don't remember what size they are. Probably you need 17 19 21. But the bolts on top of the bellhousing are a PITA, especially on the driver's side b/c there is a wiring harness in the way.
You'll want to have a 1/2" breaker bar, a very long extension, a regular long extension, u joint, and sockets for them. it's straightforward, just akward. Ben |
Originally Posted by Ben
(Post 121544)
I don't remember what size they are. Probably you need 17 19 21. But the bolts on top of the bellhousing are a PITA, especially on the driver's side b/c there is a wiring harness in the way.
You'll want to have a 1/2" breaker bar, a very long extension, a regular long extension, u joint, and sockets for them. it's straightforward, just akward. Ben |
go to harbor freight and get the wobble extensions. You can get all the bellhousing bolts with clever combinations of those and the right 3/8" sockets.
Just stack them socket-short-med-long-etc-wrench and you'll have the wrench free under the car and enough room to guide the socket with your other hand. |
DUDE, print out these pages:
http://www.miata.net/garage/clutch2.html I copied all the photos into a word file and printed them separately. Then read through this entire thread, the guy who wrote it took lots of pictures and is pretty smart... and good looking: https://www.miataturbo.net/forums/showthread.php?t=5860 |
Bell housing bolts = 17mm
Starter bolts = 14 mm Clutch bolts = 14mm Flywheel bolts = 19mm You need to remove the coilpack and possibly the CAS to get to the top bolts. On the starter side, there are two nut/bolt combos that require two wrenches to remove, one is 17mm and the other is 14mm. Upon assembly dont forget to reattatch the clutch line brace second bolt down on the pass, side. |
Get an impact socket set where the universal joint is built in. A 2 or 3 foot extension and a decent impact gun like an IR and you are golden. You'll have the trans out in 30 minutes.
|
I couldn't do it, the trans blew in my vw. Back to the daily driver drawing board.
|
thanks for the pictoral. After i buy a protege, I'm hitting the trans.
|
wTF getting rid of the VW for a Protege huh damn.
|
make sure your TO bearing fits the pp springs properly - one forum member had a TO seating/bearing ring that was fitting inside the bore on the pp springs.
|
Originally Posted by magnamx-5
(Post 121663)
wTF getting rid of the VW for a Protege huh damn.
|
yeah sell the fuck out of it.
|
do i really need the 1/2 drive bits, or can I get away with a breaker bar and a 3/8 air ratchet>
|
I used 1/2" breaker to get stuff loose then 1/2" air impact.
I don't know if 3/8" extensions and U joints would be tough enough. I'd go buy the 1/2" stuff to break loose, and then you can use your 3/8" impact if you want. You know you're going to pull the tranny at least one more time after this. Get the right tools. |
pull the engine. :rofl:
|
FWIW, we pulled the 6.5 turbo diesel motor in our GMC suburban. The bellhousing bolts were removed up top with 3 3/8 enxtensions and a universal joint attached to the socket. They were strong enough but if I had access to tons of 1/2" extensions then i'd have used them. If the 3/8" don't work, or they break then you know for sure you'll need 3/8", use the lifetime guaranteed tools when trying though :)
|
I'm not afraid of a socket or extension breaking. I'm afraid of my hand breaking when it slams into something hard and metal after the socket broke.
I smashed one of my fingers a few months ago when I used a ratchet to bust hardware loose instead of a breaker bar. Fucking ooowwwweee. Use the right tools. Save your hands. |
Oh man that would suck. The only ratcher i've ever broken was a 1/2" one and it was because I kicked the bastard to get a nut loose. It got the nut broke loose but didn't work with a damn afterwards. Breaker bars are essential in many automotive repairs. I'll opt to save my hands.
|
every one of the 4 times i had my tranny out, i used 3/8" for the bell housing bolts. cross members and ppf are easy enough to attack with a 1/2"
|
All times are GMT -4. The time now is 12:25 AM. |
© 2024 MH Sub I, LLC dba Internet Brands