bear204

Does anyone know why there are no latches on my 91 NA for the hardtop. I just bought a 91 org hard top but I don't have any brackets for the side latches to latch onto.

Joe Perez

iTrader: (8)

They were optional, just like the Frankenstein bolts. Lots of cars didn't have them.

They're easy to install, through you have to cut some holes in the plastic panels.

Braineack

iTrader: (62)

so long as your front latches are good you don't really need the side ones...

Tekel

iTrader: (2)

THis.

I ran a hard top for 2 years with just front latches and frankenstein bolts. You will get a little more vibrations out of it, but it is secure.

rleete

iTrader: (21)

Side latches help eliminate wind noise and squeaks. I think they also help lock the HT down tighter. Car felt stiffer with them installed.

You can get them from Partsgroup for about 30 bucks including hardware. Well worth it, IMO.

y8s

iTrader: (8)

pro tip: the plastic panels on my 2001 had little molded oval lines on the inside where you cut.

LiquidX

Ive never seen these side latches. Does anyone have pics? Im thinking of a hardtop to extend the driving period but i dont want to cut anything....

Braineack

iTrader: (62)

I took the panels out of my 93 and traced the holes on my 91, then FINALLY cut them like 2 years later.

Joe Perez

iTrader: (8)

The top isn't likely to fly off without them, however it's definately going to be noisier.

My experiance (on a 92) mirrors that of Y8s- after removing the plastic panels from the car, I found guide lines molded into the backside indicating where to cut.

The striker plate covers the cutout completely, so it doesn't have to be a perfectly accurate and clean cut.

bear204

Is there an aftermarket locking system for the HT's? I saw the ones from norcal but I want to keep the top latches quick acting. I don't have side latch brackets so I am trying to secure the top both ways with one solution. Ideas? Problem #1, No side latch bracket Problem #2 People have sticky fingers. I also saw TopLoc one. I would like to DIY this one and not have to spend 100.00. lol Its strange my car had the FS bolts but not the strike plates... Thanks for all the post already! Much appreciated.

codrus

All of the NAs had the frankenstein bolts, but only cars that came equipped with factory hardtops had the side latches. NBs w/o hardtops came with neither frankenstein bolts nor side latches.

I don't use the side latches (they don't fit with the HDHCDD non-HT roll bar that I have) and haven't really missed them. I don't use a lock, either, but then my car is rarely parked in situations where it's an issue.

--Ian

Joe Perez

iTrader: (8)

Unlatched:





Latched:





The amount of cutting is minimal, and precision is not required. It's just a bit of soft-ish plastic.




Locking, as in anti-theft?

I can't imagine that a person who is intent on breaking into your car for the purpose of stealing your top is going to be thwarted by any reasonable "locking" mechanism.

soviet

iTrader: (10)

I believe the side latches (strikers) are identical to the front latches (strikers)

At least when I took them off, I couldn't tell which ones were which.

kotomile

iTrader: (24)

Bolt that **** down with the Spec Miata plates if you're worried about theft.

Joe Perez

iTrader: (8)

They are similar, but not identical, and I'm pretty sure they are non-interchangeable.

Leafy

iTrader: (1)

And use an uncommon fastener like the 2 pin security, the triangle one, or security torx (not really uncommon any more).

richyvrlimited

iTrader: (1)

They're not interchangeable. The screws that hold them in place are in a sort of L pattern on the front latches and a triangular oat tern on the side latches.

Joe Perez

iTrader: (8)

I think he was talking about the strikers, the non-hinged parts which reside on the body rather than the top.

These are all two-screw, and while they appear quite similar, they are not identical.

richyvrlimited

iTrader: (1)

Doh, yes your right, reading comprehension fail, sorry.

kotomile

iTrader: (24)

You definitely could. Although unless the thief comes prepared with (IIRC) 13mm and 10mm wrenches/sockets and a cordless power tool to put them in he's not getting the top very quickly relative to latches.