Miata Turbo Forum - Boost cars, acquire cats.

Miata Turbo Forum - Boost cars, acquire cats. (https://www.miataturbo.net/)
-   General Miata Chat (https://www.miataturbo.net/general-miata-chat-9/)
-   -   fresh meat >:] (https://www.miataturbo.net/general-miata-chat-9/fresh-meat-%5D-53069/)

flounder 11-25-2010 06:07 PM

Nice choice! That one should have the torsen rear end stock.

I hate the tan top on a silver car though, even though mine was also tan/silver. Get a HT and yank that sucker out of there. ;)

How many miles?

sh4d0wf0xxx 11-25-2010 06:31 PM

Well

First off I didn't know it had aftermarket on there.
Strut bar.... I dunno if nb came with them
The shocks.... I guess they are good shocks... Like 100 a peice.... I dunno about the springs or anything.

Wuddo you mean torsen?

Also my Grammys friend says she has a flawless black hardtop in Cali that she said I could have if I lived there. But I don't so I MIGHT make the trip down there to get it but idk yet. She said she might just sell it on craigslist and I was like NO!!!!!!! lol

But thanks

Now time to save for I/H/E then megasquirt that b. Lol
Should I throw bigger injectors in before the ms or nah

flounder 11-25-2010 07:21 PM

From wikipedia-

The Torsen differential works just like a conventional differential but can lock up if a torque imbalance occurs, the maximum ratio of torque imbalance being defined by the Torque Bias Ratio (TBR).[3] When a Torsen has a 3:1 TBR, that means that one side of the differential can handle up to 75% while the other side would have to only handle 25% of applied torque. During acceleration under asymmetric traction conditions, so long as the higher traction side can handle the higher percentage of applied torque, no relative wheelspin will occur. When the traction difference exceeds the TBR, the slower output side of the differential receives the tractive torque of the faster wheel multiplied by the TBR; any extra torque remaining from applied torque contributes to the angular acceleration of the faster output side of the differential.


So.....you can smoke both tires on your burnout! :werd:

sh4d0wf0xxx 11-25-2010 07:24 PM

Pretty sweet! Lol

And btw 150k miles :(

sh4d0wf0xxx 11-25-2010 09:39 PM

Hmmm so this is what I'm going for in this order.

Megasquirt
Wideband
Intake
Header & exhaust
Lightweight pulleys
Bigger injectors ...... I dunno what size though...
Then boost it to 250 hp turbo'd :)

In that order
Any concerns?

wittyworks 11-25-2010 10:10 PM

Lightweight pulleys?? And erase intake header and exhaust, all that is covered with the turbo...

sh4d0wf0xxx 11-26-2010 01:01 AM

meant underdrive

then a pulley set to dress up the engine :P

Cococarbine3 11-26-2010 01:04 AM

Absolutely do NOT get an underdrive pulley. Search here, you'll thank me later. Pulley set?? Is that what people look at when the hood is popped these days? No. Nobody cares about your pulleys. Save your money, focus your car budget on cooler things, like getting turboed... Bling is instant gratification, but looks can be deceiving.

To make your windows faster, take the door panel off and remove the plethora of solidified OEM grease from the window rails that are causing them to slow down.

sh4d0wf0xxx 11-26-2010 03:37 AM

Lol at the window. That was gonna be my next question lol

Thank you!

Should I even bother boostin it with 150k?

sh4d0wf0xxx 11-26-2010 03:56 AM

Doing some research.....

Something about adjusting the timing from 10 to 14 degrees to give it more power..... Correct me if I am wrong.... This will increase power by a bit along with a cut cat with a straight pipe in it's place?

Can someone inform me a little bit more please?

flounder 11-26-2010 10:56 AM

I don't think the stock clutch will handle 250hp. I plan on going from 6-7 psi to around 10-11 psi over the winter and i'll be upgrading the clutch, injectors and adding an intercooler to do so. My clutch has been fine so far at 6-7 psi but I don't abuse the car that often and barely ever launch it hard.

If your concerned about your engine, a few simple tests can determine if it's healthy enough or not. I did a ring/hone and had a valve job done prior to the turbo kit going on, but it probably wasn't necessary.

Increasing the timing is good if your staying NA. Otherwise you'll need to retard it for boost. Unfortunately, the nb's require either a piggyback unit or a custom built ecm to control timing. I think yours has variable cam timing as well a higher compression ratio, so you'll have to address that too.

Is this your daily driver or do you still have that sweet 4 door cavi?

sh4d0wf0xxx 11-26-2010 03:10 PM

HAHA sorry i forgot to name the clutch.
but yeah
i was going to swap to a performance clutch right as i buy a turbo kit.

i don't plan on cheaping out on anything. so, so far i believe i can get to 250hp with a budget around $5000 in new parts. but i am going to buy some used parts and get help from you guys so i know whether the part is shitty or if it is good.

the only thing that really concerns me about my engine is the lifter tick on a cold startup and it ticks for about a minute then fades away.

ahh ok then. will i have to get lower compression pistons so it won't blow or should i be good?
...... and to be honest, i don't know what variable cam timing is..... i've heard of it but i still don't know. what i do know is that i still have TONS to learn before i start this build.

i still have the cavy, but i am getting the head all cleaned up and throwing a new head gasket on. then i gotta bypass my heater core, troubleshoot my misfire [i believe it is one of the coils in the coil pack], then i gotta pick up 2 new sensors.
I LOVE driving the miata though!

sh4d0wf0xxx 11-26-2010 03:11 PM

but yeah, going out to give her a wash, nice day out.
ill take pics after. :]

sh4d0wf0xxx 11-26-2010 07:56 PM

fixed passenger window....... Cococarbine3 youre a genius! :]
next criss angel right there knowing what i was about to ask :P


anyways i ripped off that stupid bracket in the front and took off the red sticker in the back.

That brought me here:

Washed and cleaned up and taken to the warehouses:
[Did not wash the rims because the paint is chipping. So. Yeah, they are dirty]

http://img7.imageshack.us/img7/4944/img0241fk.jpg

http://img23.imageshack.us/img23/80/img0242gr.jpg

http://img12.imageshack.us/img12/4710/img0243oe.jpg

http://img256.imageshack.us/img256/9358/img0244e.jpg

http://img249.imageshack.us/img249/7290/img0245k.jpg

http://img198.imageshack.us/img198/4210/img0246b0.jpg

http://img228.imageshack.us/img228/1266/img0247t0.jpg

http://img29.imageshack.us/img29/7546/img0248cq.jpg

http://img715.imageshack.us/img715/9830/img0249n0.jpg

http://img812.imageshack.us/img812/2925/img0250q.jpg

flounder 11-26-2010 08:53 PM


Originally Posted by sh4d0wf0xxx (Post 661590)
I beat a civic, gsr, and then I beAt a 6 cylinder mustang by like 3 or 4 car lengths

That vct must do wonders on the 01+miatas, I could hardly beat a minivan pre turbo. :rofl:

No longer do I fear the grand caravan.

sh4d0wf0xxx 11-26-2010 08:55 PM

lmfao


All times are GMT -4. The time now is 07:34 PM.


© 2024 MH Sub I, LLC dba Internet Brands