Front R Package Spoiler Installation
I don't have any mounting hardware for my R front spoiler. I'm assuming that I simply clamp it in place and drill the bottom of the front bumper at the lip's mounting points, and install a flange bolt (or bolt with washer) and tighten it with a flange nut (or standard nut with washer).
Anything I need to know? I might go install this thing when I get home tonight, if I feel like it. |
Mine is held on with stainless screws and every 6 inches or so.
__________________ Best Car Insurance | Auto Protection Today | FREE Trade-In Quote |
sounds about right.
|
Ben, bunch of 10mm bolts with nuts along the bottom, 2 self tapping screws at the edges of the bumper/lip in the fender well. 2 self tapping screws into the undertray at the ends of the brake ducts.
They come with "vampire" clips, but they are not required. |
Originally Posted by reddroptop
(Post 292542)
Ben, bunch of 10mm bolts with nuts along the bottom, 2 self tapping screws at the edges of the bumper/lip in the fender well. 2 self tapping screws into the undertray at the ends of the brake ducts.
They come with "vampire" clips, but they are not required. |
clamps to hold and pop rivets to fasten ftw :D
|
Yea go with pop rivets if you can. I had two of them stolen because they were just held on by 10MM bolts.
|
no rivet gun. bolts will work.
|
If this post isn't too late, I'd suggest fender washers as well...
- L |
I assume you already have it attached, but for future reference for others, if you aren't the only driver of your car (i.e., if you have to let someone less attentive drive it periodically to keep peace at home), I suggest mounting the front spoiler with nylon fasteners from the hardware store. That way, when the other driver pulls up INTO a parking bumper for the nth time, the spoiler will break off rather than rip to shreds. FWIW
|
Originally Posted by Ben
(Post 292604)
no rivet gun. bolts will work.
I bought the harbor freight one for 35.00 or so. If you've ever have to do 3/16" stainless rivets the gun is worth its weight in gold. I agree with them and suggest going this route. Make sure to get backing plates along with the rivets since you're riveting urethane. They are little washers you put on the other side of the rivet to keep the rivet from stretching the urethane. |
Was this Justin's busted one? Let's see some pics of the repair!
|
I'm the only driver. Ball & Chain can't operate the manual trans.
Rivets might be best, but it's getting held on with 6 bolts/washers/nuts and 2 tapping screws. I don't have time to stop by HF before work (HF opens at 8 and so do I), and I am yet to have air at my house anyway. Ben, No, not really. A coworker found a better condition one on a car in the shop's back lot. This car is in the grass, not the gravel, and the vegetation was high and thick enough to mask the fact that this car was at some point a 93LE and had its front lip still there. I had the lip removed, and it's in OK shape, but was missing the top of the pass side brake duct. Justin's lip had it still, so I removed it (they're stapled on) and epoxied it to the new one. So if you want Justin's lip minus the brake duct cover, it's yours. |
Originally Posted by Ben
(Post 292897)
So if you want Justin's lip minus the brake duct cover, it's yours.
|
You guys were right; this thing needs to be riveted on. It's slightly tweaked and has a critical mounting tab missing. Rivets would make it look boo-t-full.
Mr CupCar, I know you're a busy family man, but is there any chance I could swing by maybe next weekend and use your fancy equipment? |
I used clothespins on mine, worked like a charm :D
|
All times are GMT -4. The time now is 09:49 AM. |
© 2024 MH Sub I, LLC dba Internet Brands