Pop at low rpm?
Once in a while i get a pop that sounds like its coming from the intake. I can hear it when i'm looking for parking at college and just keeping it in the low rpms. Its not a loud POP, its just a little pop here and there but its loud enough to notice with the radio in low volume or off. I hear it a bit more when i'm backing out from a parking spot and i'm just keeping it at about 1500 rpm. I can also hear something that sounds like a pop when i have the hood open and i open up the throttle just a bit to rev it (2k rpm max) when i let it go i hear few pops as the engine is decelerating but i dont know if its the same thing. It is not a continuous pop pop pop pop.
What do you guys think? bad valve? something with the egr? bad timing? |
could be tons of shit... details on your setup?
|
1 Attachment(s)
all stock sir, I removed the little L pipe horn that comes out of the stock air box to increase response. Now its a bit louder under acceleration and obviously response is much better. Step on the gas it revs right away, before it felt more like drive by wire.
(the horn that comes out of the air box on the right of the pic is what i'm talking about) thats a pic of my car. Anybody know that alarm on the left? Let me know if i purchased your car off the dealer :D. Attachment 203405 On a side note, what do i do with the washer fluid when i install the turbo? Where do i relocate it? Yes i have abs on the other end. |
where's the turbo? Seriously, are people driving these cars around without turbos?
|
Originally Posted by hustler
(Post 462900)
where's the turbo? Seriously, are people driving these cars around without turbos?
When i first bought the car, i got 6 months warranty and then apperently mazda didnt want to accept it since it was a '99 with out charging 400 application fee if i want the 6 months warranty. The dealership called me and they said because we made the deal, they will pay the fee for mazda to take it but only for a 3 months warranty (200 bucks). I told the guy i will think about it. I'm currently at the point where i can cancel the warranty and get my 350 bucks back or i can have another month and a half of drive train warranty. |
It's probably the overrun fuel cut. Basically over a certain RPM and no load (accelorator not pressed, engine braking) the ECU will cut fuel completely.
At a certain RPM it will start injecting fuel again. Depending on when that happens you might get a small backfire through the intake. I don't think it's anything to worry about. |
could it be backfire into the exhaust and into the egr?
I know i heard it a lot of backfire on my bike but never at low rpm like its on the miata. |
its probly a dirty 02 sensor letting you laod up in criuse and backfire becouse of unburnt gas in the exhaust either that or, you car has hella bad carbon build up and is detonating this would be very bad. So i would
Check the compression Check or change the 02 sensore seriusly its like 13 bucks And depending on your results from these 2 you will have a pathway to a solution gl/ |
Originally Posted by magnamx-5
(Post 462951)
check or change the 02 sensore seriusly its like 13 bucks/
|
alright well i toyed around with it on my way out, i'm very sure it only happens after i let off the gas (aka decelerating).
On to looking for tools for compression test. |
yep this further confirms my to rich sentiments it is a good sign. :D
|
where do you guys disco the spark and the fuel when doing a compression test?
|
dont worry about the fuel part just disconnect the coils.
|
where do you do that? at the coils or is there a fuse? (never done compression test, sorry for my newbness)
ggrr bloody search shows everything BUT a compression test writeup also where do you find O2 sensor for 13 bucks? |
For compression check,
Step 1 – Drive car a bit to get it warmed up and top off the battery charge. Step 2 – Let it cool down and then pull All 4 spark plugs out Step 3 – Disconnect CAS to eliminate spark and fuel injection (OR FUEL INJECTION RELAY) Step 4 – Screw compression tester into cylinder 1 nearest to radiator Step 5 – With foot down all the way on the gas (WOT), turn the key to start and hold until the engine has turned 8-10 times and pressure no longer climbs on the gauge. Step 6 – Record pressure on gauge and release air to zero and remove gauge from spark plug hole . Step 7 – repeat steps 4-6 for each cylinder moving from front to back of engine. Step 8 – Check pressures and make sure no readings are more than 10-15% different You should get yourself a manual... |
if you dont have a long flexible foot you can also just prop the throttle body open with something on the outside.
As for the 02 sensor just go to the auto parts store and get a generic 02 sensor. At the most it is 4 wires. Do you know how to deal with joining wires in any way shape or form? Have you ever done any other automotive maintenance to anything? |
i'm pretty handy with stuff however i'm nervous when i try new things that i've never done before such as messing with the coils... thats my main problem. As for wires, i can do wires quite well :), so its not an actual plug though, you have to cut and slash? The main reason why i ask is because i looked around for a o2 sensor and they are about 70-80 bucks on the web.
|
After figuring out your issue, do your turbo install now. You don't need the drivetrain warranty. These engines are very strong and that's why we turbocharge them. As for the transmission, unless you drive your car like a mortard it will be more than strong enough to be raced with stock power- spec miata proves that. The turbo is not really that difficult of a project; it is the beginning that will encourage and motivate you to work on your car more. I am probably one of the least mechanically and automotive service stuff knowledgeable people on the site but in a few weeks I'm pulling my engine to replace it and do a bunch of other work. The internet is my friend and your friend for "how-tos". I waited two years to turbocharge and that was a waste of time when I could have dramatically shortened the duration of my drives :).
|
i'm not too shabby about installing the turbo, i've read up on the stuff and i feel pretty confident about the hardware, I've never messed around with the xede that i bought to play around for the fuel but Stephanie is helping me out with that so i should be good.
The only thing i'm a little nervous about when doing the turbo is ripping out bolts since i have a lot of experience in that being in the rust belt :D. I've ripped out upwards of 9/16" diameter bolts when i was doing my control arms on my jeep 2 years ago :D Undoing the tiny 3/8" nuts on the exhaust makes me very damn nervous, other than that i feel confident that i can install the turbo with no problems. I just want to confirm the motor is running in top shape possible. If something needs to be fixed, i'll take the warranty, get it fixed and install the turbo :) |
|
All times are GMT -4. The time now is 08:02 PM. |
© 2024 MH Sub I, LLC dba Internet Brands