Landrew

iTrader: (2)

How can I underdrive my 50W fog bulbs so they last forever as my Canadian DRL lights. They would still be quite visible at 40watts I would guess and taking the volts down by XX percent should add a few thousand or more hours of life. Resistors ?? But which ones would I want ? I don't know.

I haven't tested the actual voltage to the bulbs yet.

I know that LED's last forever but I just spent a whopping $15 on a pair of Hella Yellow bulbs to go in my yellow laminated fogs so I want to explore the incandescents.

Ted75zcar

iTrader: (2)

Resistors = probably not. Well, you could get 10W resistors, but certainly not the best way.

Look into the ebay voltage step down modules similar to this:

131558369217 but higher power

DNMakinson

iTrader: (3)

<p>&nbsp;</p><p>I understand that running halogens at low voltage disturbs the redeposition cycle, and may not lead to increased life. https://en.wikipedia.org/wiki/Halogen_lamp</p><p>&nbsp;</p>

Landrew

iTrader: (2)

DC Step Down Adjustable Power Supply

I'll look into these thanks

Landrew

iTrader: (2)

I'm hoping to only underdrive them a little bit. For example if they are getting say 13.5V at the lights I'd like to take it down to 13 or 12.5V.

I should measure my headlights V as that is what the Canadian cars use as DRL's - a lower voltage is sent to the headlights so that they last much, much longer.

patsmx5

iTrader: (16)

If you wanted to loose only 0.5-1.0 volts, smaller diameter wiring/worst ground will get you there. Essentially using wire as a resistor.

Or possibly look into using a DRL module from another car directly? Might be the easy button.

NiklasFalk

iTrader: (1)

How do halogens respond to PWM?

Schuyler

iTrader: (1)

<p></p><p>That won't change the desired current draw from the lights.The wires just won't be able to handle it and might melt/break.</p>

Joe Perez

iTrader: (8)

You know the dimmable halogen floor lamps which occasionally set curtains on fire? The dimmers in those use a form of PWM (phase angle control) to chop the AC waveform using a Triac or a pair of SCRs.

Ted75zcar

iTrader: (2)

The thermal relaxation of the filiment is going to be way too slow to care about a chopper or pwm.

Landrew

iTrader: (2)

Much more technical than in was expecting.
I thought I could thrown in a few resistors like my ATV heated grips run when in the low setting and call it a day. - Ceramic Resistor

Ted75zcar

iTrader: (2)

Yep, something along those lines would work. If you go that route, be sure to mount the resistors to a suitable heat sink.

Joe Perez

iTrader: (8)

You can, but as Ted noted, they will generate quite a lot of heat, so mount them appropriately.

Assuming a lamp is rated for 50 watts at 14 volts, it's got a resistance of 3.92 ohms. If you put a 1 ohm resistor in series with it, total system wattage will drop to 40 watts, of which the resistor will be dissipating about 8 watts and the lamp will be dissipating about 32.

Leafy

iTrader: (1)

You know, 100W 10ohm resistors are like 6 bucks on amazon prime. Sounds pretty easy to me.

Landrew

iTrader: (2)

Sweet, I will try this.

They will be mounted around the front fender and get some airflow.

Ted75zcar

iTrader: (2)

Conduction >> convection

NiklasFalk

iTrader: (1)

The simplest way would be to couple them in series, but 7V might be too low.
Requires very little in parts.

Landrew

iTrader: (2)

ebayed some gold aluminum housed 1 ohm 100 watt resistors. It'll take 2 weeks to get here. I'll be playing with the DRL and side markers until they show up.

BarbyCar

iTrader: (1)

I did this with a relay one time, wired so that I could switch from series to parallel.

Landrew

iTrader: (2)

FYI on a Canadian made car the DRL modules black with white wire is the one that activates the headlight DRL's. remove it and its manual only.

With that out of the way and the resistors having shown up I proceeded to install my Hella yellows into the fogs.

Resistored light on the passenger side regular in drivers. Yes that resistor gets hot, we will see how it survives down there. Trying it this way and see how things go for a few months.