Braineack

iTrader: (62)

Customary "doughnut video" to follow on Saturday.

I only drove around the block a bit, but can feel the difference, cant wait to test it out on Saturday for my first autox of the season.

BTW, Brian, preload tested at around 190ft/lbs.

m2cupcar

iTrader: (5)

mmmmm.... ell, ess, dee
sounds like you shimmed it- do you have the specs/thickness on your shims, and what you used? which rear?

Braineack

iTrader: (62)

it was from a 84-85 GSL. Pulled it out, bolted on the ring gear, swapped it in, and dropped it off with a guy to set it up.

To test, I put one wheel on the ground, put a torque wrench to the axle bolt started at 40ft/lbs. untill i hit about 190 it would slip. Is that the correct way to test?

Al Hounos

It makes the car a lot more fun, doesn't it.

I do kinda wish I had put shims in though, the plates were at full OEM spec thickness, but I guess OEM just isn't very stiff.

sbrian2

iTrader: (12)

I've got mine all built up with new parts and one of the thicker washers per side, but not in the car yet. 190 ft-lbs sounds very tight, you almost have a locker!!!

Braineack

iTrader: (62)

did i perform that test correctly? It definatly felt different than my vlsd in the 2 minutes i drove it. Had cold RT215s on it and swung the rear out easier than ever. Took some good corners and it gripped great.

sbrian2

iTrader: (12)

Yeah, I would say so. One wheel locked and turn the axle nut until it breaks free and at the torque rating it does is what your preload is. Did you feel the tires skip any at low speed like pulling into a parking spot? My wife's Trailblazer SS does that when you first pull it out of the garage and the fluid is still cold.

Braineack

iTrader: (62)

I'm going to chalk it up to "I dont give a ****" and just enjoy it as is, without caring. :gay:

neogenesis2004

iTrader: (12)

**** yo couch!

m2cupcar

iTrader: (5)

that sounds like a proper check to me. Mine had all discs within spec when I got it, but I was still planning on shims. I thought I'd have the cash to build it with 3.63 gears... but that still hasn't come about.

y8s

iTrader: (8)

when I get my car back on the ground I'll do that same test and see what I get with my kaaz.

oh and brainsy, I still have $75 in cashish in my nightstand for your 3.9 setup!

Braineack

iTrader: (62)

I still got it sitting in my car

m2cupcar

iTrader: (5)

Are bidding? plus trade?

Braineack

iTrader: (62)

what you say?

neogenesis2004

iTrader: (12)

trade him for fe3 -> miata motor mounts

m2cupcar

iTrader: (5)

he's a 1.6 purist.
I have a 4.10 sitting on the floor of the garage next to my rx-7 lsd.

neogenesis2004

iTrader: (12)

I was saying for me, lol. I keep "subtly" hinting at it to you :P **** even a piece of paper with circles drawn on it that I could drill out on plate metal would rock.

m2cupcar

iTrader: (5)

Damn- ok. Subtle is something I expect from a woman. :gay:
PM'd - just make sure you print them at 100% and match them to your miata motor mounts first.

neogenesis2004

iTrader: (12)

Hey scott, send that box of samoas to rob, he deserves it.

m2cupcar

iTrader: (5)

unless serves us some donuts this weekend- then he gets them all!