Good news and bad news. No wait, just bad. Now some good
06-03-2014, 12:24 AM
#61
Cpt. Slow
Thread Starter
iTrader: (25)
Join Date: Oct 2005
Location: Oregon City, OR
Posts: 14,179
Total Cats: 1,129
Get rid of the porsche. Stat.
Push your car in to it's place, and reap the benefits of a garage.
This should quickly be followed by pulling the oil pump plug and/or the sandwich plate.
Push your car in to it's place, and reap the benefits of a garage.
This should quickly be followed by pulling the oil pump plug and/or the sandwich plate.
Reply
0
0
06-03-2014, 10:38 AM
#62
mkturbo.com
iTrader: (24)
Join Date: May 2006
Location: Charleston SC
Posts: 15,176
Total Cats: 1,680
I'd hope so, but given everything going on...I can't help but go straight to worse-case scenario. Unfortunately, this oil has not been driven on. This is the oil I put in it and have cranked up the engine on for maybe all of 30 seconds, and spun over a fair bit trying to build pressure. The engine has already been through the oil you put in it, oil I put in it to drive it home and now this round of oil. I'd think that metal flakes should long be gone.
Not to look at MT for mental therapy, but there is other **** going on in my life that is not just the car situation, and it's all piling up and sucking dry my motivation to give a **** about anything. I just need something to go 'good' soon...and it seems getting to drive my car home last Monday was going to be that thing...until this **** happened.
Not to look at MT for mental therapy, but there is other **** going on in my life that is not just the car situation, and it's all piling up and sucking dry my motivation to give a **** about anything. I just need something to go 'good' soon...and it seems getting to drive my car home last Monday was going to be that thing...until this **** happened.
Reply
0
0
06-03-2014, 12:22 PM
#67
Just curious - is it possible for you to have Josh or whoever dropped it in for you diagnose it? If you have no garage and/or tools to troubleshoot this properly.
I was going to say "oil pump isn't that hard to replace, you don't even need to yank the engine" but then you're working in a parking lot with what I'm assuming only the bare essential tools, so it might be a pain.
I was going to say "oil pump isn't that hard to replace, you don't even need to yank the engine" but then you're working in a parking lot with what I'm assuming only the bare essential tools, so it might be a pain.
Reply
0
0
06-03-2014, 12:49 PM
#71
When I was diagnosing the cam trigger issue on that engine, it took about 10 minutes (no joke) to take off the whole front of the engine and have the water pump/oil pump completely exposed and ready to come out.
Maybe I'm missing something?
I know its not like pulling the valve cover, but still. It aint hard. I'm not sure you appreciate how simple these engines are compared to some others (esp newer cars)
PS: I feel OP's pain, because just a month or two ago I was almost in the same predicament, except over a completely unrelated issue.
Maybe I'm missing something?
I know its not like pulling the valve cover, but still. It aint hard. I'm not sure you appreciate how simple these engines are compared to some others (esp newer cars)
PS: I feel OP's pain, because just a month or two ago I was almost in the same predicament, except over a completely unrelated issue.
Reply
0
0
06-03-2014, 01:05 PM
#74
...if only there were a way to access the ******* relief valve without pulling the pump.
The twenty-five dollar and thirty-sever cent question is- Is there a "fix" for the relief valve or is it better to just replace the whole damn thing? I'm seriously contemplating putting myself in a bit of a financial pickle in order to have the car back on the road ASAP and that plan involves sucking up for the BE pump.....
This is assuming that when the pan gets pulled, the metal flecks I found in the oil aren't of concern :/
The twenty-five dollar and thirty-sever cent question is- Is there a "fix" for the relief valve or is it better to just replace the whole damn thing? I'm seriously contemplating putting myself in a bit of a financial pickle in order to have the car back on the road ASAP and that plan involves sucking up for the BE pump.....
This is assuming that when the pan gets pulled, the metal flecks I found in the oil aren't of concern :/
Reply
0
0
06-03-2014, 01:11 PM
#75
Cpt. Slow
Thread Starter
iTrader: (25)
Join Date: Oct 2005
Location: Oregon City, OR
Posts: 14,179
Total Cats: 1,129
What's the price difference? that vvt pump is expensive, but if it's still a few hundred dollars, I wouldn't stress your money situation any further. It's just a car.
First task needs to be getting rid of the Porsche, while simultaneously signing up for a car-to-go program. You can't keep working on it if every time it needs to go back together and cleaned up. Often the first few hours of car work is spent getting it on jack stands, wheels off, your space organized, and removing a few things. You can't keep wasting your time doing that every day.
First task needs to be getting rid of the Porsche, while simultaneously signing up for a car-to-go program. You can't keep working on it if every time it needs to go back together and cleaned up. Often the first few hours of car work is spent getting it on jack stands, wheels off, your space organized, and removing a few things. You can't keep wasting your time doing that every day.
Reply
0
0
