Braineack

iTrader: (62)

History: When I first wired my solenoid I put the diode on the wires about 2" off the valve. Then I proceeded to wrap it in electrical tape as if I was trying to suffocate it. I was also smart used two black wires off the valve so I later, if I ever need to, I could not determine which is which.

Flash Forward: In my haste to get my car running I seem to have connected my solenoid backwards so the wrong end of the diode saw the 12v source. Over the past few day of finally driving the new car I've had a supercharger like boost as I'm only at wastegate. EBC was not operable. So pulled the wiring apart to see that the diode on the wiring was fried. Fixed. Still nothing. So I open the MS and find part of the circuit fried. Fixed. Now I say I found my lost boost. Much Improved. (I'll post pics of the board later, need to download off camera). Still missing about 500RPM of spool, but better than before....traction is a thing of the past again.

Braineack

iTrader: (62)

btdubz, my MAT still doesn't budge. But it always reads accurate, how neat-o.

Savington

iTrader: (31)

methinks 13.0 is a bit lean there, buddy-o

Braineack

iTrader: (62)

yeah i know, cells we untuned. 11.0:1 is rich too, i dont wait for no 160*F.


aiight here's the trace that blow out...glad i saw it, i was scratching my head on this one for a few minutes because i had no connectivity between the AIC hole and the DB37.

Savington

iTrader: (31)

why would you untune a cell

Braineack

iTrader: (62)

because i never hit those cells before, that was my first log since getting the EBC working. like I got it working, pulled out of my parking spot, logged it, and parked the car and posted.

notice the other log overlayed? When warmup is not on, that **** was perfectly flat at 12:1 - 11.8:1

samnavy

iTrader: (7)

I only see RPM/MAP/Boost(psi) in the first box, but I see 4 lines.
I'm also wondering why MAP and Boost are different lines... don't both of those read off the internal MAP sensor?

Braineack

iTrader: (62)

lines are the same, just so you can see both readings, makes it easier to see 12psi not 180kPa.

y8s

iTrader: (8)

map's not there but the four lines are "before" and "after" overlayed.

elesjuan

iTrader: (11)

@12psi your MAT is 98 degrees?!

ThePass

iTrader: (3)

Yeah what's with that MAT??

Joe Perez

iTrader: (8)

Yeah, seems a bit high to me as well... Probably it was a warm day in Atlanta.

Is there a reason the boost seems to rise much more slowly until about 3k in the "after" trace? Without seeing TPS it's hard to know what was going on.

cjernigan

iTrader: (13)

Looks like his MAT at 12 psi is 86* and at 8 psi its 75*. You guys are reading the max MAT temp he saw over the entire datalog. That is probably when he was at idle and the sensor heat soaked.

Braineack

iTrader: (62)

s

My AIT sensor reads dead on based off an external thermometer, if the sensor is reading high inside the pipes at idle and I remove it from the bung and blow on it so it can read ambient temps, it's dead on within seconds.



Ok, I believe my issue with my lost spool was because I always forget that my pedal should go to to floor. Did some ninja tuning on the way to work:

Zabac

iTrader: (39)

Glad to hear this Scott, I bet it's a good feeling to have boost, even if it's again, I should be so lucky to feel so for myself soon.
Scott builds two turbo Miatas, me not even one yet. :(

y8s

iTrader: (8)

it helps to show the TPS in the datalog.

and since when is scott in atlanta?

Joe Perez

iTrader: (8)

D'oh!

Hey- Atlanta, Arlington, Chicago, Phoenix, they're all in that weird part of the country east of I-15 where you can't get good fish tacos.

And the comment about the MAT being "a bit high" was a joke. After a long boosted pull I routinely see 90-100°F even on cold days. Here's one from yesterday morning. If I recall correctly, this was up a slight hill:

Ben

iTrader: (33)

Excuse you, good sir, as I believe you may have misspoken. It is my firm belief that Athens, GA (just outside of Atlanta) indeed has some of the best fish tacos in the country, if not the world.

But perhaps we speak about different things?

Braineack

iTrader: (62)

helps if i had a TPS installed. on the list.

y8s

iTrader: (8)

is there a proper spelling of the word "d'ohwned"?