Big noob cant get car started with MS2
02-12-2012, 03:54 PM
#23
Elite Member
iTrader: (10)
Join Date: Jun 2006
Location: Athens, Greece
Posts: 5,976
Total Cats: 355
Ok, go to the boost control menu (Advanced -> Boost control settings) and switch it off. Hit Burn, switch off the ignition off for 5 seconds and then back on - does the message go away?
Reply
0
0
02-12-2012, 04:05 PM
#25
Senior Member
Thread Starter
iTrader: (1)
Join Date: May 2010
Location: Harrisburg, Pa
Posts: 581
Total Cats: 8
The config error went away but it still won't start. Also looking at the gauge cluster on tuner studio the arf is different then whats showing on the gauge
Reply
0
0
02-12-2012, 04:16 PM
#29
Slowest Progress Ever
iTrader: (26)
Join Date: Oct 2007
Location: The coal ridden hills of Pennsylvania
Posts: 6,022
Total Cats: 304
The wideband reading difference would also have nothing to do with it not starting.
Reply
0
0
02-12-2012, 04:25 PM
#34
Slowest Progress Ever
iTrader: (26)
Join Date: Oct 2007
Location: The coal ridden hills of Pennsylvania
Posts: 6,022
Total Cats: 304
What I meant is in the lc1 software you need to have it setup a certain way...it's software issue not the physical connection...
Let me get off my phone and get on my pc and upload a photo.
Let me get off my phone and get on my pc and upload a photo.
Reply
0
0
02-12-2012, 04:30 PM
#36
Senior Member
Thread Starter
iTrader: (1)
Join Date: May 2010
Location: Harrisburg, Pa
Posts: 581
Total Cats: 8
17 Warnings:
Warning: MSQ Units Mismatch for egoTemp! °F found in current configuration, �F found in MSQ, values were not converted to new units.
Warning: MSQ Units Mismatch for tempTable! °F found in current configuration, �F found in MSQ, values were not converted to new units.
Warning: MSQ Units Mismatch for clt0! °F found in current configuration, �F found in MSQ, values were not converted to new units.
Warning: Parameter in msq, but not valid for current firmware: No options found for Bit EcuParameter:tempUnits
Warning: MSQ Units Mismatch for IdleHyst! °F found in current configuration, �F found in MSQ, values were not converted to new units.
Warning: MSQ Units Mismatch for fastIdleT! °F found in current configuration, �F found in MSQ, values were not converted to new units.
Warning: MSQ Units Mismatch for IACcoldtmp! °F found in current configuration, �F found in MSQ, values were not converted to new units.
Warning: MSQ Units Mismatch for mat0! °F found in current configuration, �F found in MSQ, values were not converted to new units.
Warning: MSQ Units Mismatch for pwmidle_crank_clt_temps! °F found in current configuration, �F found in MSQ, values were not converted to new units.
Warning: MSQ Units Mismatch for matCorrTemps! °F found in current configuration, �F found in MSQ, values were not converted to new units.
Warning: MSQ Units Mismatch for pwmidle_clt_temps! °F found in current configuration, �F found in MSQ, values were not converted to new units.
Warning: MSQ Units Mismatch for temp_table_p5! °F found in current configuration, �F found in MSQ, values were not converted to new units.
Warning: MSQ Units Mismatch for fc_clt! °F found in current configuration, �F found in MSQ, values were not converted to new units.
Warning: MSQ Units Mismatch for matTemps! °F found in current configuration, �F found in MSQ, values were not converted to new units.
Warning: MSQ Units Mismatch for N2OClt! °F found in current configuration, �F found in MSQ, values were not converted to new units.
Warning: MSQ Units Mismatch for idleadvance_clt! °F found in current configuration, �F found in MSQ, values were not converted to new units.
Warning: MSQ Units Mismatch for RevLimLookup! °F found in current configuration, �F found in MSQ, values were not converted to new units.
Reply
0
0
