Big noob cant get car started with MS2
#45
Elite Member
iTrader: (10)
Join Date: Jun 2006
Location: Athens, Greece
Posts: 5,976
Total Cats: 355
What's your current ambient temperature? You probably need to open up the idle valve more when cranking (Startup/idle -> PWM idle cranking duty) and then add some more enrichment in the ASE percentage table.
#46
Senior Member
Thread Starter
iTrader: (1)
Join Date: May 2010
Location: Harrisburg, Pa
Posts: 581
Total Cats: 8
It's about 50*F in my garage. Side note. I told my buddies I got it to start. Of course they bring this over...
Last edited by gorillazfan1023; 02-12-2012 at 05:15 PM. Reason: photo
#47
Senior Member
Thread Starter
iTrader: (1)
Join Date: May 2010
Location: Harrisburg, Pa
Posts: 581
Total Cats: 8
I don't know if that photo worked, here's the link http://www.flickr.com/photos/7649989...in/photostream
#49
Slowest Progress Ever
iTrader: (26)
Join Date: Oct 2007
Location: The coal ridden hills of Pennsylvania
Posts: 6,022
Total Cats: 304
If you can start it, can you hold your foot on the throttle until it warms up? See if that makes it idle better when the engine warms up...
I'm not talking flat to the floor, I'm talking like 1,500 rpm's.
I'm not talking flat to the floor, I'm talking like 1,500 rpm's.
#50
Slowest Progress Ever
iTrader: (26)
Join Date: Oct 2007
Location: The coal ridden hills of Pennsylvania
Posts: 6,022
Total Cats: 304
Your LC-1 wiring doesn't need to be exactly like this, but just use this as a reference that 1 wire goes to the gauge and a different wire goes to the MS. They need to be set differently as pictured. You need to go into your Innovate software and connect your laptop to only the LC1. In there you can change the outputs of the LC1. Change them to what the pictured wires are set at, and then go into tuner studio (after connecting to MS), and make sure the wideband input is the same as what you set the one going to MS as.
Ex: If you set the LC1 output to MS for 0-5V 10-20:1, then in tuner studio it should be also set for 0-5v 10-20:1. Then both the MS and the LC1 gauge will read the same.
#51
Senior Member
Thread Starter
iTrader: (1)
Join Date: May 2010
Location: Harrisburg, Pa
Posts: 581
Total Cats: 8
Hahaha. One excessively wealthy one. I'll have to post pics later of the rest of his cars. I have my cranking duty at 64.8 60.2 then 44.9 42.2. Is that ok? also increased ASE percentage to 50 at the coldest then 49 48 45 etc downward. Sound alright? I will try to keep the revs up
#53
Slowest Progress Ever
iTrader: (26)
Join Date: Oct 2007
Location: The coal ridden hills of Pennsylvania
Posts: 6,022
Total Cats: 304
With the car off, make sure your TPS is calibrated correctly. If so, then "it dies if you hit the throttle" might be too much fuel. Does it idle long enough to get an AFR reading?
Do you know how to post a screen shot of your fuel table?
Do you know how to post a screen shot of your fuel table?
#56
Senior Member
Thread Starter
iTrader: (1)
Join Date: May 2010
Location: Harrisburg, Pa
Posts: 581
Total Cats: 8
Attachment 34200
Ex: If you set the LC1 output to MS for 0-5V 10-20:1, then in tuner studio it should be also set for 0-5v 10-20:1. Then both the MS and the LC1 gauge will read the same.
Ex: If you set the LC1 output to MS for 0-5V 10-20:1, then in tuner studio it should be also set for 0-5v 10-20:1. Then both the MS and the LC1 gauge will read the same.
#58
Slowest Progress Ever
iTrader: (26)
Join Date: Oct 2007
Location: The coal ridden hills of Pennsylvania
Posts: 6,022
Total Cats: 304
If you got the LC1 settings, then that's like the hardest part. My laptop was being a Dick when I tried to connect it to my LC1. That was like 3 years ago though.
I'm glad to see you're making progress and that your car is soon ready to hit the street!
I'm glad to see you're making progress and that your car is soon ready to hit the street!
#59
Senior Member
Thread Starter
iTrader: (1)
Join Date: May 2010
Location: Harrisburg, Pa
Posts: 581
Total Cats: 8
Yeah connecting was pain. I am an idiot. So I get it setup and turn the key to on and there CEL odd going crazy. Then I remember I forgot to refill my coolant so it thinks it's really hot. I can't wait to hit the street either. My exhaust sounds awesome