DIYAutotune Base Map / Firmware mismatch, TunerStudio Errors
 

Hey y'all. Got my DIYPNP all assembled and successfully flashed the latest MS2/Extra 3.4.2 firmware onto it. I connected it to TunerStudio out of the car just using the 12v power adaptor they sell, and TS recognized it just fine. So I loaded the base map from the DIYPNP instructions but it spit out a list of 46 errors. I did some searching here and elswhere and it seems most of the are likely inconsequential but I'm not sure enough of that to plug it into the car... I've copied the errors below, anyone have any advice? Someone mentioned emailing DIYAutotune to see if they have an updated base map, has anyone had success with that?

Error list:

46 Warnings:
Warning: MSQ Units Mismatch for knk_tadv! s found in current configuration, sec found in MSQ, values were not converted to new units.
Warning: MSQ Units Mismatch for amap_table2! kPa found in current configuration, % found in MSQ, values were not converted to new units.
Warning: MSQ Units Mismatch for amap_table1! kPa found in current configuration, % found in MSQ, values were not converted to new units.
Warning: Parameter in .msq, but not valid for current firmware: No options found for Bit EcuParameter:can_poll equal to the proposed Disabled
Warning: Parameter in .msq, but not valid for current firmware: No options found for Bit EcuParameter:flexport equal to the proposed JS11
Warning: Parameter in .msq, but not valid for current firmware: No options found for Bit EcuParameter:spk_config_spka equal to the proposed D14
Warning: MSQ Units Mismatch for knk_trtd! s found in current configuration, sec found in MSQ, values were not converted to new units.
Warning: MSQ Units Mismatch for IACcrankxt! s found in current configuration, sec found in MSQ, values were not converted to new units.
Warning: Parameter in .msq, but not valid for current firmware: No options found for Bit EcuParameter:rtbaroport equal to the proposed MS2 AD6/JS5
Warning: Parameter in .msq, but not valid for current firmware: No options found for Bit EcuParameter:knkport equal to the proposed MS2 AD7/JS4
Warning: Parameter in .msq, but not valid for current firmware: No options found for Bit EcuParameter:IdleCtl equal to the proposed PWM Closed-loop
Warning: Parameter in .msq, but not valid for current firmware: No options found for Bit EcuParameter:ego2port equal to the proposed MS2 AD6/JS5
Warning: MSQ Units Mismatch for smap_injadv3! kPa found in current configuration, % found in MSQ, values were not converted to new units.
Warning: MSQ Units Mismatch for EAElagRPMmax! rpm found in current configuration, rpms found in MSQ, values were not converted to new units.
Warning: MSQ Units Mismatch for fc_ego_delay! s found in current configuration, seconds found in MSQ, values were not converted to new units.
Warning: MSQ Units Mismatch for pwmidle_targ_ramptime! s found in current configuration, sec found in MSQ, values were not converted to new units.
Warning: MSQ Units Mismatch for pwmidle_close_delay! s found in current configuration, sec found in MSQ, values were not converted to new units.
Warning: baroCorrVals array size does not match the currently loaded configuration,
rescaled .msq values to match configuration.
Warning: MSQ Units Mismatch for pwmidle_pid_wait_timer! s found in current configuration, sec found in MSQ, values were not converted to new units.
Warning: baroCorrDelta array size does not match the currently loaded configuration,
rescaled .msq values to match configuration.
Warning: Parameter in .msq, but not valid for current firmware: No options found for Bit EcuParameter:tacho_opt3f equal to the proposed IGN (JS10)
Warning: Parameter in .msq, but not valid for current firmware: No options found for Bit EcuParameter:launch_opt_pins equal to the proposed PE0/JS7
Warning: MSQ Units Mismatch for RotarySplitLoad! kPa found in current configuration, % found in MSQ, values were not converted to new units.
Warning: MSQ Units Mismatch for smap_table1! kPa found in current configuration, % found in MSQ, values were not converted to new units.
Warning: Parameter in .msq, but not valid for current firmware: No options found for Bit EcuParameter:N2Oopt_pins2 equal to the proposed IAC1+2
Warning: Parameter in .msq, but not valid for current firmware: No options found for Bit EcuParameter:N2Oopt_pins equal to the proposed PE0/JS7
Warning: MSQ Units Mismatch for idleadvance_delay! s found in current configuration, sec found in MSQ, values were not converted to new units.
Warning: MSQ Units Mismatch for fmap_trim1! kPa found in current configuration, % found in MSQ, values were not converted to new units.
Warning: idleadvance_loads array size does not match the currently loaded configuration,
rescaled .msq values to match configuration.
Warning: MSQ Units Mismatch for smap_injadv2! kPa found in current configuration, % found in MSQ, values were not converted to new units.
Warning: MSQ Units Mismatch for smap_injadv1! kPa found in current configuration, % found in MSQ, values were not converted to new units.
Warning: Parameter in .msq, but not valid for current firmware: No options found for Bit EcuParameter:testop_coil equal to the proposed CoilB
Warning: idleadvance_curve array size does not match the currently loaded configuration,
rescaled .msq values to match configuration.
Warning: MSQ Units Mismatch for smap_table3! kPa found in current configuration, % found in MSQ, values were not converted to new units.
Warning: Parameter in .msq, but not valid for current firmware: No options found for Bit EcuParameter:testop_inj equal to the proposed Neither
Warning: MSQ Units Mismatch for fmap_trim1doz! kPa found in current configuration, % found in MSQ, values were not converted to new units.
Warning: MSQ Units Mismatch for fmap_table3doz! kPa found in current configuration, % found in MSQ, values were not converted to new units.
Warning: MSQ Units Mismatch for fmap_table1doz! kPa found in current configuration, % found in MSQ, values were not converted to new units.
Warning: MSQ Units Mismatch for fmap_table1! kPa found in current configuration, % found in MSQ, values were not converted to new units.
Warning: MSQ Units Mismatch for fmap_table3! kPa found in current configuration, % found in MSQ, values were not converted to new units.
Warning: MSQ Units Mismatch for fmap_trim2! kPa found in current configuration, % found in MSQ, values were not converted to new units.
Warning: MSQ Units Mismatch for fmap_trim4! kPa found in current configuration, % found in MSQ, values were not converted to new units.
Warning: MSQ Units Mismatch for fmap_trim3! kPa found in current configuration, % found in MSQ, values were not converted to new units.
Warning: MSQ Units Mismatch for fmap_trim3doz! kPa found in current configuration, % found in MSQ, values were not converted to new units.
Warning: MSQ Units Mismatch for fmap_trim2doz! kPa found in current configuration, % found in MSQ, values were not converted to new units.
Warning: MSQ Units Mismatch for fmap_trim4doz! kPa found in current configuration, % found in MSQ, values were not converted to new units.

Trubokitty.com