You did calibrate the TPS, right?

please don't arbitrarily change my settings, the basemap was setup exactly for YOUR ms. It shares little in common with a DIYPNP.



It actually appears as though I swapped the ckp/cmp inputs on the harness.

Only change from stock is MSD spark plug wires.

Went ahead and changed to DIY's ignition settings. Could not find anything for:

- skip pules - box on left
- spark A output pin

- fixed advance - box on right
- use prediction


Great point on the flood clear. Tried to change it to 110% to take away authority, and it does not allow.

Can not set the TPS at all. It reads 1023 no matter where the pedal is pressed.

Attachment 186028

My bad, defer to Brain. I didn't realize this was the case.

nevermind.

is this a drop in the mail procedure or easy enough for me to attempt?

who am i kidding- dropping in the mail tomorrow.

Why not reload Brain's map and see what can be done with it? You have plenty of time before tomorrow & can still mail it out if need be.

Might as well learn by doing, then in the future you will have an idea of how everything works if something goes wrong instead of having to mail off your MS every time...

there are some hardware issues. I proved myself incapable of soldering when I blew up a 14point7 build.

need MS guru help
 

Brain swapped 3J and 3H, the two Cam inputs. He also checked the CLT and TPS, which both worked fine on the stim.

CLT and TPS are still not connecting properly. I directly connected red/blue on 2E from this wiring diagram to the Yellow 2E on the pinout below, and it is still not reading coolant temp.

https://www.miataturbo.net/attachmen...ine=1330453175


Scott is thinking they share a ground and it could be faulty. Any idea where this ground is located?


Any other ideas??

I should add, coolant temp read fine on the dash before attempting any of this.

Yeah, I'm a bit clueless on this. I did mistakenly have the cam/crank inputs crossed on the harness like I suspected after seeing the composite log posted by Shane. I corrected this.

But I know the TPS and CLT were wired correcly on the harness and functioned fine on the stim, but I checked it against 3 different diagrams to be certain--plus those functions had always been working when it was an MSI and I didn't touch them when modding to MSII.

My only guess right now is that the ground in the engine bay is missing. Correct me if I'm wrong, but I'm pretty sure that would cause the CLT sensor to sit at 180°F (which is failsafe IIRC) and the TPS to sit at full 5v. Unless there's a ground in the engine harness I missed that's required,

...acutally now that I think about it I almost remember something to this matter. I think I did the three grounds above and not to the 3F as well, that may be what's missing here.


Yeah, now I'm pretty certain that's the issue.

The missing ground was the problem. All sensors are reading now!


I have made two attempts at starting, and it has not fired up yet. Attached is datalog, msq, and .ini.

Let's get her started!!!! (help me please)

edit: I guess I can not upload the .ini

getting RPMs in TS? I cant see those files here at work.

EDIT: looks like youre getting some reading, can you do a shot of the composite logger again?

Yes, I am getting RPM. Reads around 160 while cranking.

For some wierd reason, I can not open the composit logger. It is greyed out, and I can not click on it. Will try to reboot everything and try again.

oh yeah, that's due to the firmware.

Is this far too rich? I have req fuel at 11.9, and I am still using the stock 99 injectors.

Whats up with the GEGO?

Also surprised where the MAP sits.


Attachment 186018

doesnt seem to be spinning fast enough to pul lenough vacuum. sound like it's struggling?

Not really. I put jumper cables on to up the charge, and still spun at that speed.

I also lowered cranking speed in the settings to 160 as well as lowered cranking pulsewidth.

Pulled #1 plug. Smells like gas but is not wet.

The actual cranking speed is low, get a decent battery. You are not pulling enough vacuum and your cranking pulsewidth is also low if you still have the stock injectors in.