Miata Turbo Forum - Boost cars, acquire cats.
Page 2 of 2
1
2
Show 60 post(s) from this thread on one page

Miata Turbo Forum - Boost cars, acquire cats. (https://www.miataturbo.net/)
-   MEGAsquirt (https://www.miataturbo.net/megasquirt-18/)
-   -   MS-controlled VICS (https://www.miataturbo.net/megasquirt-18/ms-controlled-vics-32509/)

18psi 04-05-2017 04:55 PM
we'll know in 8 years if it worked

keep your fingers crossed

18psi 04-05-2017 04:55 PM
we'll know in 8 years if it worked

keep your fingers crossed

WestfieldMX5 04-08-2017 03:45 AM
And to make sure we're all connecting it correctly for the next 8 years to come, configure your output like this:

Enabled: check
Power On Value: ON
Active Value: OFF
RPM > 5250 (YMMV)
Hysteresis 200 (YMMV)

Who here dares to admit that he has been running it backwards for the past 8 years? Anyone, Anyone ... Bueller?

PS I believe these settings would do the same, but not going to break my head over it ;), notice the < instead of >.

ON / ON / < 5250
OFF / ON / < 5250
https://cimg4.ibsrv.net/gimg/www.mia...76cb70ada9.jpg

The Driver 04-11-2017 12:40 PM
Originally Posted by Savington (Post 1403742)
  1. Connect one side to +12v, the other side to spare on/off output on the ECU
  2. Configure programmable i/o in software to activate at 2500rpm (close butterflies), deactive at ~5500rpm (open butterflies) (actual RPMs will vary depending on dyno testing)
  3. ?????
  4. profit
Thanks!

Savington 04-11-2017 01:08 PM
Originally Posted by The Driver (Post 1405166)
Thanks!
Definitely replace step 2 with what Frank posted above, his settings are better.

shuiend 04-11-2017 01:10 PM
I sent Driver a pm as he was asking me about it last weekend at Miatapalooza. I let him know that at least for the MS3X that braineack builds that he uses the Nitrous1 output to control vics. Not sure what the MSLabs or MS3Pro use, but I would guess it is similar.

phil21191 04-11-2017 03:01 PM
Originally Posted by shuiend (Post 1405173)
I sent Driver a pm as he was asking me about it last weekend at Miatapalooza. I let him know that at least for the MS3X that braineack builds that he uses the Nitrous1 output to control vics. Not sure what the MSLabs or MS3Pro use, but I would guess it is similar.
Looks like Rev uses an output on his own CAN expander for the MSLabs units. At least that's how its configured on my '99 MS2 Enhanced from him

https://cimg4.ibsrv.net/gimg/www.mia...a8c5febd88.png

The Driver 04-21-2017 04:29 PM
Originally Posted by WestfieldMX5 (Post 1404505)
And to make sure we're all connecting it correctly for the next 8 years to come, configure your output like this:

Enabled: check
Power On Value: ON
Active Value: OFF
RPM > 5250 (YMMV)
Hysteresis 200 (YMMV)

Who here dares to admit that he has been running it backwards for the past 8 years? Anyone, Anyone ... Bueller?

PS I believe these settings would do the same, but not going to break my head over it ;), notice the < instead of >.

ON / ON / < 5250
OFF / ON / < 5250
https://cimg4.ibsrv.net/gimg/www.mia...76cb70ada9.jpg
Please, forgive my ignorance. Will I have to add this values to the MS3, after the VICS is hooked up? I haven't played with the Tuner Studio (shoot, I haven't downloaded yet). Thanks for your help!

Braineack 04-21-2017 04:39 PM
this is how mine are setup:
https://cimg0.ibsrv.net/gimg/www.mia...4145d5bf11.png

The Driver 04-27-2017 10:02 PM
The guy that hooked the VICS, had 'Tuner Studio". Oh man, the car is FUN!


All times are GMT -4. The time now is 11:17 AM.
Page 2 of 2
1
2
Show 60 post(s) from this thread on one page


© 2024 MH Sub I, LLC dba Internet Brands