2 Attachment(s)
the orange wire i added for launch control
https://www.miataturbo.net/attachmen...ine=1338922580 https://www.miataturbo.net/attachmen...ine=1338922580 |
1 Attachment(s)
yeah, you need to move the blue and green wires and add a 100-300ohm reistors on each as such:
Green wires: https://www.miataturbo.net/attachmen...ine=1338923846 then youll use NON INVERTED for the spark output method. should see the dropouts go away, luckily your ignitor is still healthy. you can probably go ahead and add that capacitor and remove c30 as well. |
i just slide the housings off the green and blue wires, they have a 330ohm resistor on each, would that be to much to reuse?
O O B G |
yeah but they arent going to the right spot and they aren't pullu p resistors, they are inline so far as i can tell.
look at the diagram i posted and compare how they go into the board (led side only) |
1 Attachment(s)
i can solder them in if needed be. i dont have the money to order anything lol
https://www.miataturbo.net/attachmen...ine=1338927059 |
2 Attachment(s)
do this and change the spark setting. in the least this will solve the issue...well more than likely.
https://www.miataturbo.net/attachmen...1&d=1338928589 |
1 Attachment(s)
|
1 Attachment(s)
should i eliminate these? im not sure what they are for
https://www.miataturbo.net/attachmen...ine=1338929504 |
no just try what i said.
|
now it wont start, just cranks
|
Its missing r24 and r26 isn't it?
|
Yeah in the top pic of the board...see the two missing resisotrs by the leds? You need those. 1k iircc
|
Originally Posted by Braineack
(Post 885907)
Yeah in the top pic of the board...see the two missing resisotrs by the leds? You need those. 1k iircc
|
Yeah that. You'll need them. You can steal from elsewhere on the board on sec and ill figure it out
EDIT: sorry was on phone. steal from r42 and r55, they are next to each other, center of the board. put them in r26 and r29. |
Originally Posted by Braineack
(Post 885913)
Yeah that. You'll need them. You can steal from elsewhere on the board on sec and ill figure it out
EDIT: sorry was on phone. steal from r42 and r55, they are next to each other, center of the board. put them in r26 and r29. one question, i noticed on the diagram you have above, it shows there should be a 1k resistor between iac1a and js8 for tach, then 470 for iac1a to another spot if you look at my pic, look at my brown wire for tach, its missing the 1k, and it had another resistor running from the js8 to another hole across from it, not where shown in the diagram |
still no start
|
maybe you need to revert ( just lift one leg of r44 and r52 back up, you dont need to replace them back), but that should have done it.
|
Originally Posted by Braineack
(Post 885943)
maybe you need to revert ( just lift one leg of r44 and r52 back up, you dont need to replace them back), but that should have done it.
|
it was 42 and 55, you moved them to 26 and 29 correct?
sorry, im on my phone and going from my poor memory when im replying. |
Originally Posted by Braineack
(Post 885946)
it was 42 and 55, you moved them to 26 and 29 correct?
sorry, im on my phone and going from my poor memory when im replying. if it makes any different, the tach isnt moving any of the attempts yet |
All times are GMT -4. The time now is 10:28 PM. |
© 2024 MH Sub I, LLC dba Internet Brands