Sequential Ignition question on an "MSPNP1.5"
#1
Junior Member
Thread Starter
iTrader: (4)
Join Date: Nov 2011
Location: Ft Lauderdale, FL
Posts: 79
Total Cats: 0
Sequential Ignition question on an "MSPNP1.5"
Hey guys,
I'm installing an MS2 daughterboard on an MSPNP1 to make an "MSPNP1.5". I'm going to mod the MS2 DB so that I can bring PT6 and PT7 directly to JP2.38 and 36 (JS0 and JS2 on the v3.57 board). Then I'm going to wire the signals to a DIYPNP sequential ignition module and bring out INJ-3 and INJ-4 out to the MSPNP daughterboard.
The question I have is about the wiring. I plan on wiring it up as follows:
INJ-1 -> 2U -> Fuel Injector #1
INJ-2 -> 2V -> Fuel Injector #3
INJ-3 -> 2Y -> Fuel Injector #4
INJ-4 -> 2Z -> Fuel Injector #2
Is this correct?
I'm installing an MS2 daughterboard on an MSPNP1 to make an "MSPNP1.5". I'm going to mod the MS2 DB so that I can bring PT6 and PT7 directly to JP2.38 and 36 (JS0 and JS2 on the v3.57 board). Then I'm going to wire the signals to a DIYPNP sequential ignition module and bring out INJ-3 and INJ-4 out to the MSPNP daughterboard.
The question I have is about the wiring. I plan on wiring it up as follows:
INJ-1 -> 2U -> Fuel Injector #1
INJ-2 -> 2V -> Fuel Injector #3
INJ-3 -> 2Y -> Fuel Injector #4
INJ-4 -> 2Z -> Fuel Injector #2
Is this correct?
#6
Boost Czar
iTrader: (62)
Join Date: May 2005
Location: Chantilly, VA
Posts: 79,493
Total Cats: 4,080
the parts you need to do seq. injection costs about $2 for all four, fwiw. i wouldn't buy the diypnp module for a v3.57 board install.
you need (4) vnd5n07 drivers, (4) 1K resistors, and (4) 100K resistors. that's it.
you dont have any wires on 2y and 2z, so that idea is void. you'll have to run the two extra wires out to the engine bay, and rewire the harness so that you wire the outputs correctly to each cylinder.
you need (4) vnd5n07 drivers, (4) 1K resistors, and (4) 100K resistors. that's it.
you dont have any wires on 2y and 2z, so that idea is void. you'll have to run the two extra wires out to the engine bay, and rewire the harness so that you wire the outputs correctly to each cylinder.
#8
Junior Member
Thread Starter
iTrader: (4)
Join Date: Nov 2011
Location: Ft Lauderdale, FL
Posts: 79
Total Cats: 0
Yeah the circuit looks pretty basic. I'll see if I can get some free samples from some of my distributor contacts. Worst case, I'll give Digikey a ring. Do you know if Radio Shack has the vnd5n07s?
#11
Elite Member
iTrader: (10)
Join Date: Jun 2006
Location: Athens, Greece
Posts: 5,977
Total Cats: 356
Yes, but different drivers have different on-state resistance for example. So one driver could actually flow less current than another driver, or take more/less time to open/close the injector.
Thread
Thread Starter
Forum
Replies
Last Post
bigmackloud
Miata parts for sale/trade
19
01-08-2021 11:24 AM
JesseTheNoob
DIY Turbo Discussion
15
09-30-2015 02:44 PM