Thought that started in 93?
|
Why do you have both pins listed for the injector. Why is 34/35 listed.
|
Originally Posted by curly
(Post 1291451)
Do you have a Californian Miata?
I have tested my injector circuits and everything checks out fine. I ground pins 21/22 on the U1 socket and inj1 and inj2 LED turns on. I am so lost... I referenced this site to help troubleshoot the injector driver circuit: http://www.diyautotune.com/tech_arti...leshooting.htm |
Originally Posted by aidandj
(Post 1291453)
Why do you have both pins listed for the injector. Why is 34/35 listed.
|
Why do you have both 34 and 35 connected to the injector wire?
|
Originally Posted by aidandj
(Post 1291467)
Why do you have both 34 and 35 connected to the injector wire?
I did the same thing with pins 32/33 for injectors 1/3. (Bank 1, in batch fire mode) |
makes sense. Different than ms3. But I've never played with ms2.
Did you try swaping the wires around and seeing if the wet cylinders switch? |
Originally Posted by aidandj
(Post 1291473)
makes sense. Different than ms3. But I've never played with ms2.
Did you try swaping the wires around and seeing if the wet cylinders switch? The misfire note seems a bit closer and smoother now. The revs are peppier. I wonder if my copper plugs are done from all the fouling and such. I am now stuck between a rock and a hard place.... |
Did you put new plugs in?
|
Originally Posted by aidandj
(Post 1291603)
Did you put new plugs in?
I'll test for continuity again from the MS harness to the injector harness.:confused: |
Which 2 arent firing. Stop doing random stuff and figure out which ones arent firing and why.
|
Originally Posted by aidandj
(Post 1291632)
Which 2 arent firing. Stop doing random stuff and figure out which ones arent firing and why.
|
But he didnt swap the wiring and check again. Because that would narrow down the problem.
|
Originally Posted by aidandj
(Post 1291645)
But he didnt swap the wiring and check again. Because that would narrow down the problem.
|
Are you using output test mode to test this?
|
Originally Posted by aidandj
(Post 1291645)
But he didnt swap the wiring and check again. Because that would narrow down the problem.
As of right now, I checked for 12v on each lead on the 4 harness plugs and they checked out fine. I also checked continuity from the injector harness all the way to pins 32/33 and 34/35. Continuity as expected. This leads me to the board. I have the MS on the bench hooked up to a Jimstim. I also have 2 injectors with the pigtails hooked up. The black wires is hooked up to constant 12v, and the green/white wires hooked up to injector bank 1 and 2 respectively. Injector bank 2 is non responsive. This is my issue. What is weird tho, I tested the injector circuit by grounding pins 21 and 22 on U1 and the LED's for inj1 and inj2 turn on. Based on the link I provided above, this indicates the injector drivers are operational.... however, I don't think that is the case based on where I am at now. |
I only read teh first post:
you messed up on your wiring and you probably only have 2 spark plugs or two injectors firing. |
Originally Posted by ennjay
(Post 1291671)
Injector bank 2 is non responsive. This is my issue. What is weird tho, I tested the injector circuit by grounding pins 21 and 22 on U1 and the LED's for inj1 and inj2 turn on. Based on the link I provided above, this indicates the injector drivers are operational...
The injectors are run off the U4 IC. you probably should inspect how you build the board and see if youre not missing something on the injector circuits. |
Originally Posted by Braineack
(Post 1291751)
the LED circuits are for Spark, not injectors.
The injectors are run off the U4 IC. you probably should inspect how you build the board and see if youre not missing something on the injector circuits. I am currently focusing on the U4 IC and all other components to ensure continuity and that certain voltage values are present in on/off conditions. When I was referring to LED, I was referring to the JimStim LED's that are marked Inj1 and Inj2, not the LED on the MS. For testing, I connected an injector to the JimStim to replicate what is on my car. I hooked up one end of the pigtail to 12v and the other to Inj1 and Inj2 terminal on the jimstim. The injectors pulse on inj1 terminal which is expected. When I connect to inj2 terminal, NOTHING - no response or clicking. To my luck, I shorted something on the JimStim while connecting the Injector and now my C1 and F2 are shorted (assuming) because they both get hot as hell after a few seconds of the jimstim being on. Then after a few seconds, the jimstim stops powering the MS. Thanks for the help again. My plan to address the short on my JimStim so I can continue troubleshooting the U4 IC. |
All times are GMT -4. The time now is 12:35 PM. |
© 2024 MH Sub I, LLC dba Internet Brands