EBC still doesn't work
04-05-2008, 05:49 PM
#1
Senior Member
Thread Starter
iTrader: (8)
Join Date: Aug 2006
Location: Springfield, IL
Posts: 1,012
Total Cats: 0
EBC still doesn't work
To start this off I have searched everyones problems with this topic. Still no go I checked my 12V source its actually like 13 but, shouldn't affect anything? Tried changing all my boost duty cycles to 0 and it still just stays totally closed, and hits the overboost protection no matter what I do? At first I thought it was just the insulator but braineak fixed that and still nothing. I also read where cjernigan had to make his opposite to work. Tried that also still nothing? What do I need to do? Any advice will be nice thanks guys
Reply
0
0
04-05-2008, 08:38 PM
#4
Oh geez. 
Download the latest hi-res here: http://msextra.com/viewtopic.php?t=25336
Then easytherm it with the correct values and use easytherm to reflash the ECU. Unplug your coils if you're doing this in the car. Then load a new MSQ before reconnecting the coils. Once you have flashed the .s19 and loaded the msq you can connect the coils and not worry about that anymore.
To create a new msq, open megatune and select the new project folder when the window pops up. (Put the 10F folder in the "megasquirt" folder if you haven't already) Then copy all of the settings over for each window.
Or just get the firmware flashed and try your old msq first to see if that fixes it.
Does your boostDC gauge show any activiity?
Download the latest hi-res here: http://msextra.com/viewtopic.php?t=25336
Then easytherm it with the correct values and use easytherm to reflash the ECU. Unplug your coils if you're doing this in the car. Then load a new MSQ before reconnecting the coils. Once you have flashed the .s19 and loaded the msq you can connect the coils and not worry about that anymore.
To create a new msq, open megatune and select the new project folder when the window pops up. (Put the 10F folder in the "megasquirt" folder if you haven't already) Then copy all of the settings over for each window.
Or just get the firmware flashed and try your old msq first to see if that fixes it.
Does your boostDC gauge show any activiity?
Reply
0
0
04-05-2008, 08:49 PM
#5
Senior Member
Thread Starter
iTrader: (8)
Join Date: Aug 2006
Location: Springfield, IL
Posts: 1,012
Total Cats: 0
Oh geez.
Download the latest hi-res here: http://msextra.com/viewtopic.php?t=25336
Then easytherm it with the correct values and use easytherm to reflash the ECU. Unplug your coils if you're doing this in the car. Then load a new MSQ before reconnecting the coils. Once you have flashed the .s19 and loaded the msq you can connect the coils and not worry about that anymore.
To create a new msq, open megatune and select the new project folder when the window pops up. (Put the 10F folder in the "megasquirt" folder if you haven't already) Then copy all of the settings over for each window.
Or just get the firmware flashed and try your old msq first to see if that fixes it.
Does your boostDC gauge show any activiity?
Download the latest hi-res here: http://msextra.com/viewtopic.php?t=25336
Then easytherm it with the correct values and use easytherm to reflash the ECU. Unplug your coils if you're doing this in the car. Then load a new MSQ before reconnecting the coils. Once you have flashed the .s19 and loaded the msq you can connect the coils and not worry about that anymore.
To create a new msq, open megatune and select the new project folder when the window pops up. (Put the 10F folder in the "megasquirt" folder if you haven't already) Then copy all of the settings over for each window.
Or just get the firmware flashed and try your old msq first to see if that fixes it.
Does your boostDC gauge show any activiity?
wait Ive done that before oooops but I cant find that gauge I've tried to find it? The only place I can find a boost duty cycle gauge is under the tuning tab and that shows it changing but no affect? where is that gauge? under a different title maybe?
Reply
0
0
04-07-2008, 09:32 PM
#14
Senior Member
Thread Starter
iTrader: (8)
Join Date: Aug 2006
Location: Springfield, IL
Posts: 1,012
Total Cats: 0
Oh geez.
Download the latest hi-res here: http://msextra.com/viewtopic.php?t=25336
Then easytherm it with the correct values and use easytherm to reflash the ECU. Unplug your coils if you're doing this in the car. Then load a new MSQ before reconnecting the coils. Once you have flashed the .s19 and loaded the msq you can connect the coils and not worry about that anymore.
To create a new msq, open megatune and select the new project folder when the window pops up. (Put the 10F folder in the "megasquirt" folder if you haven't already) Then copy all of the settings over for each window.
Or just get the firmware flashed and try your old msq first to see if that fixes it.
Does your boostDC gauge show any activiity?
Download the latest hi-res here: http://msextra.com/viewtopic.php?t=25336
Then easytherm it with the correct values and use easytherm to reflash the ECU. Unplug your coils if you're doing this in the car. Then load a new MSQ before reconnecting the coils. Once you have flashed the .s19 and loaded the msq you can connect the coils and not worry about that anymore.
To create a new msq, open megatune and select the new project folder when the window pops up. (Put the 10F folder in the "megasquirt" folder if you haven't already) Then copy all of the settings over for each window.
Or just get the firmware flashed and try your old msq first to see if that fixes it.
Does your boostDC gauge show any activiity?
I reflashed it with the easytherm and It didnt fix the EBC so I'm trying to make an all new msq but I dont ever get a choice of new project?
Last edited by turbobluemiata; 04-07-2008 at 11:37 PM.
Reply
0
0
Thread
Thread Starter
Forum
Replies
Last Post
Frank_and_Beans
Supercharger Discussion
13
09-12-2016 08:17 PM
