baron340

iTrader: (5)

So, I've been digging through schematics and researching for quite a while now trying to learn how to make my MS2 have sequential injection. I didn't assemble this board and I've just hit a brick wall with all of the possibilities. I know that my particular MS2 only has 2 injector drivers. I know how to solder to a board, and how most electronics components work. What I don't know is exactly what I need to install or connect to where to get sequential injection working. I know for sequential ignition I would need a crank position sensor. But the CAS is sufficient for injection, correct? So here are some pics of what I'm working with. Can I make this work in the proto area with some simple components? Do I need to buy the diypnp doo-dad on diyautotune's site? Someone help me out please. I can provide more detailed pictures or descriptions if needed.

Braineack

iTrader: (62)

BRAIN: Hey awesome, I built that MS!

OBAMA: You didn't build that.

Braineack

iTrader: (62)

Basically all 4 injectors need the same driver. It's easier if you build 4 new injector drivers circuits at the same time.

I like to copy the circuit on the DIYPNP/MS3X, which uses 1 driver and 2 resistors each. Very simply and works well.

But to make life even easier, you could buy this board: 4-Channel Ignition/Injection Driver Board

and follow the documenation here: Sequential Injection Code for MS2

read through it like 4-5 times.

hustler

iTrader: (6)

Obeezy

Braineack

iTrader: (62)

Fo-sheezy.

baron340

iTrader: (5)

Sweet, thanks for the help Brain. My awesome gub'ment network won't let me check the second link at work. I'll have a look when I get home. But it looks like that is exactly the information I needed to make this work.

Braineack

iTrader: (62)

weird, it's the same server.

I have to use a token to view, myself. But I cant access the second...It wont load if you open in a second tab, but it will if I load in the same tab I logged in with.

baron340

iTrader: (5)

So if I understand correctly, I can use this schematic for the MS3x. I build 2 more injector driver circuits (assuming these already match the existing 2) or build 4 new ones with the same components. I jump the FET output to the corresponding pins on the 37 pin ouput connector. But where do I pull the injector number 3 and 4 FET inputs from? It would be PA2 and PA3 on the diagram? I really hate to pay $50 for a board and $5 in components when I have the capability to make my own circuit boards if I need to. Either that, or shouldn't I be able to use the on board proto area and then sink the FET's to the case like the others?

Braineack

iTrader: (62)

all four drivers need to match. so if you build the above, you need to build all 4.


if you read the docs I posted, it explains where the outputs go. you have to mod the ms2 daughterboard and remove the cpu clock circuit from the mainboard (not really all of it, just the components touching a certain spot).


here:



The picture below shows the placement on the V3.0 board of the 4 injector channels. The standard injector drivers components can be left on the board but will be unused and will not interfere with injector channels 1 and 2. The injectors channels 3 and 4 connect to pads originally used for the MS1 clock circuit and require the removal of those components for proper and safe operation. The injector channel 3 shows 2 pads because they correspond to the same electrical location (use either one). The components to remove are: R21,C20,C21,R22,R23,Y1,C24,C25.

baron340

iTrader: (5)

Ah ok, I was making it much harder than it needed to be. Thanks again for the help brain. I don't care what the president says, you did build that.

baron340

iTrader: (5)

you have spare 1-2-3 available along with the current 2 INJ outputs.

correct.