Not starting
So I finally got my MS to read everything and with harness from Braineack it should fire up but... Motor turns over and tries to start but doesn't...
I tried MSPNP settings for 9495 version - nothing :/ |
Req fuel is set? IIRC, you have to reset your cranking pulsewidths as well. You did both of those?
|
If you get fires but its not starting, maybe a backfire after enough cranking, try swapping the ign wires on your MS board and firing it up then. Alot of times they are just backwards. Just try it, can't hurt anything.
|
I'm pretty sure i matched his outputs on the MS board to match his harness. If they were backwards and it was trying to start, he'd get really weird pulses of the engine trying to turn the crank back down on itself.
try setting your tps values. and make sure your laptop is hooked up and when you crank you see rpms. I put your tach signal on 4F which should be correct. |
i triple-checked every wire - its correct. ill try to calibrate tps tonight and play with cranking pulse widths.
ps: i get from 200 to 500 rpm on crank. |
if it sees rpm and you're getting spark which you said you were, and the ecu controls fuel, it should start up.
listen to make sure the coil outputs aren't reversed. it will try to pop and almost stop trying to crank. whats happening is it's firing when the piston is still traveling up. however, I'm 95% positive it wont. |
it doesnt. it tries to start but it seems like it doesnt get enough fuel. and i had a backfire on one of the extensive cranks.
|
backfire usually means too much fuel ;)
|
well, after 20 cranks which didnt work i bet there is enough fuel in engine to backfire ;)
|
so i reversed my spark plug wires and it started! but extremely roughly... and then... after 10 minutes... it died completely and now it wont start at all!!!!!!!
it was running extremely rough and was sputtering until i loaded 1.6t map - then it was all good for about 4-5 minutes and then it died... i reversed my wires back, hooked up stock ecu, and now i get no spark!! did i fry my coils or just messed up wires?? |
Was your spark setting set to inverted or non-inverted? What was your dwell set to?
|
i used mspnp 9495 settings.
|
Do you have a 9495 PNP?
So then why did you use those settings? :slap: |
well, they worked :)
|
yup, she flew. all the way to the scene of the crash.
Maybe you'll read up on why that was a bad idea, replace what you fried, and fix your mistakes. |
so do you think i fried my coils?
|
http://www.allfordmustangs.com/forum...oot_myself.gif
Not sure what kind of dwell they're running, though it should have been set right in terms of being setup for non-inverted spark. |
it was 5.5 crank and 4.4 running...
|
|
I run 2.6 on my '99, no idea what the 96 needs.
|
shit... i think im due for new coil then :/
|
Might as well go COP then. Cheaper than a coil from the dealer. Hopefully you can get a 2nd hand one cheap otherwise.
|
i need to get car running tomorrow so im getting next day shipping from moss
|
fuck... $228
|
by the way, when car was running, it was showing 4.4 afr... is that my narrowband acting up? ill switch to lc-1 tomorrow
|
Get that LC-1 installed, narrows are worthless. Please tell me you didn't just spend that much money on a new coil?
|
actually, they couldnt deliver it to me today... so i called my buddy at his shop and got myself a replacement... for $274 :/
nobody has one cheaper who can ship it today :/ |
If i wher ordering oem type shit i would ge the upgraded coil pack from moss.
|
those are only for 1.6
|
^^^ megasquirt can use any coilpack as long as you know dwell times i believe.
|
no, his problem would be that the 1.8 coil packs have the ignitor built in and the 1.6 have the ignitor separate. So he can't use 1.6 coil packs because he would be missing the ignitor.
|
ah.. all the reason to go COP :)
|
All times are GMT -4. The time now is 11:34 AM. |
© 2024 MH Sub I, LLC dba Internet Brands