MEGAsquirt A place to collectively sort out this megasquirt gizmo

Acceleration Enrichment

Thread Tools
 
Search this Thread
 
Old 04-23-2017, 10:48 PM
  #1  
Senior Member
Thread Starter
 
poormxdad's Avatar
 
Join Date: Dec 2010
Posts: 1,191
Total Cats: 103
Default Acceleration Enrichment

Gents,

I spent some time trying to tune the AE TPSdot. I have a lot of work to do, but just playing with the 50 and 200%/sec columns has brought some positive results.

Would any of you be willing to share your plots? I'm more interested in the shape of you graphs and the decel section than I am in the actual numbers you have.

Thanks much,
Attached Thumbnails Acceleration Enrichment-accelenrich.jpg  
poormxdad is offline  
Old 04-24-2017, 06:56 AM
  #2  
Boost Czar
iTrader: (62)
 
Braineack's Avatar
 
Join Date: May 2005
Location: Chantilly, VA
Posts: 79,493
Total Cats: 4,080
Default

I dont really like your table.

when I'm tuning Accel-pump, I like a 0 TPSdot column, then the next one right around where my threshold is, so in your case 15.

so my table might look like this on the tpsdot row: -500 -100 -50 0 15 25 50 200 400

this table is focused on you tip-in, so you want a little more resolution at the low end of the scale where you'll be most affected by leanness. You may find 16% adder at 50 tpsdot rate a good value, but since it's interpolating to 0% adder all the way back at the -50 tpsdot rate, you may be hard to tune where it counts the most. YMMV.
Braineack is offline  
Old 04-24-2017, 09:04 AM
  #3  
Senior Member
Thread Starter
 
poormxdad's Avatar
 
Join Date: Dec 2010
Posts: 1,191
Total Cats: 103
Default

Brain,

The TPSdot row has the numbers that came with the base map. I assumed there was a reason. I'll make the changes.

Thanks,

Last edited by poormxdad; 04-24-2017 at 09:18 AM.
poormxdad is offline  
Old 04-24-2017, 10:26 AM
  #4  
Boost Czar
iTrader: (62)
 
Braineack's Avatar
 
Join Date: May 2005
Location: Chantilly, VA
Posts: 79,493
Total Cats: 4,080
Default

i dont necessarily like their basemap.
Braineack is offline  
Old 04-24-2017, 10:36 AM
  #5  
Senior Member
Thread Starter
 
poormxdad's Avatar
 
Join Date: Dec 2010
Posts: 1,191
Total Cats: 103
Default

Brain,

Do you have suggestions to start with for the negative columns?

Thanks,
poormxdad is offline  
Old 04-24-2017, 10:41 AM
  #6  
Boost Czar
iTrader: (62)
 
Braineack's Avatar
 
Join Date: May 2005
Location: Chantilly, VA
Posts: 79,493
Total Cats: 4,080
Default

keep it at 0% you don't need to tune negative much, youll see if you subtract more than about 10% of fuel it'll be noticable when you lift. it's mainly to help reduce your PW when you lift, just before overrun kicks in, otherwise it'll adversely affect drivabliity.


then once the tip-in's are dialed in, you'll wanna tune EAE which will allow you to keep your AFR perfectly stable even when you maniuplate the pedal up and down.
Braineack is offline  
Old 04-24-2017, 05:34 PM
  #7  
Senior Member
Thread Starter
 
poormxdad's Avatar
 
Join Date: Dec 2010
Posts: 1,191
Total Cats: 103
Default

Originally Posted by Braineack

...so my table might look like this on the tpsdot row: -500 -100 -50 0 15 25 50 200 400
Brain,

That's one too many columns. I'm going to use -500, -50, 0, and try to tweak the positives next time I get her out of the garage unless there's a reason I need another negative column of Zero.

If I'm going to use Zeroes for the negatives, can I just have -500 and 0?

Thanks,

Last edited by poormxdad; 04-24-2017 at 06:19 PM.
poormxdad is offline  
Old 04-26-2017, 04:33 PM
  #8  
Boost Czar
iTrader: (62)
 
Braineack's Avatar
 
Join Date: May 2005
Location: Chantilly, VA
Posts: 79,493
Total Cats: 4,080
Default

that's probably sufficient.
Braineack is offline  




All times are GMT -4. The time now is 02:02 AM.