setting up LC-1
Just finished installing an LC1 to my MS1
I've set the configurator to LC-1 and in the EGO settings changed the dropdown to wideband. is that all I need to do or have I missed something? Thanks |
I'm sorry I can't help you with the MS aspect, but from my experience, you need to set up the lc-1 with lm programmer. When I got mine, none of the factory defaults were set as they should have been.
|
You need to use LM programmer and setup Analog out1 (if you use Analog out1):
0V -> 0,5 Lambda 5V -> 1,5 Lambda Then select in MT Configurator: Innovate LC-1 Default Also you need to change EGO switch point (in Exhaust gas settings) to 2.51! -> Burn to ECU. :) |
Originally Posted by disc
(Post 58033)
You need to use LM programmer and setup Analog out1 (if you use Analog out1):
0V -> 0,5 Lambda 5V -> 1,5 Lambda Then select in MT Configurator: Innovate LC-1 Default Also you need to change EGO switch point (in Exhaust gas settings) to 2.51! -> Burn to ECU. :) Welcome btw :D |
Originally Posted by disc
(Post 58033)
You need to use LM programmer and setup Analog out1 (if you use Analog out1):
0V -> 0,5 Lambda 5V -> 1,5 Lambda 0V -> 10:1 AFR 5V -> 20:1 AFR Then go in MegaTune Configurator and set: car1 -> settings.ini -> LAMBDA_SENSOR: INNOVATE_0_5_LINEAR: Innovate, PLX 0-5V 10-20:1 AFR Open your .msq in MegaTune and set: Basic Settings -> Exhaust Gas Settings -> EGO Sensor Type: Wide band, EGO Switch Point (v): 2.332, Ignition Events: 16, Controller Step Size: 1, Controller Authority 15, Active Above Coolant Temp (C): 65, Active Above RPM: 1100, EGO Correction Step Counter: mSec |
Hey! He can use whatever he want settings!
Why Active Above RPM: 1100 ? As far as I can say this guy is in the beggining of tune of his engine... so EGO correction MUST be OFF. Active Above RPM: 10000 will disable EGO correction... He even didn't say what version of firmware is using... 029q2? P.S. Sorry, but my english is not quite good, it's not my native language. |
Originally Posted by disc
(Post 58135)
Hey! He can use whatever he want settings!
Originally Posted by disc
(Post 58135)
Why Active Above RPM: 1100 ?
Originally Posted by disc
(Post 58135)
As far as I can say this guy is in the beggining of tune of his engine... so EGO correction MUST be OFF.
|
Reverant you're a ledge thanks!
|
hrm when I ro a run with logworks I get AFR's i was kinda expecting, i.e. 13-10:1 (room for improvment..)
however within megatune my afr's are displayed waaaaaay lean at around 17:1 what's wrong with that? I've double checked my settings and they all look fine to me? Help! (again!!) |
Did you make sure to change the MS settings?
|
Originally Posted by Al Hounos
(Post 58334)
Did you make sure to change the MS settings?
|
Originally Posted by richyvrlimited
(Post 58320)
hrm when I ro a run with logworks I get AFR's i was kinda expecting, i.e. 13-10:1 (room for improvment..)
however within megatune my afr's are displayed waaaaaay lean at around 17:1 what's wrong with that? I've double checked my settings and they all look fine to me? Help! (again!!) 1) Where did you ground your LC-1? You absolutely need to ground it on the same location as the Megasquirt. Different points on the chassis will not do! 2) Can you post your MS .msq and MT settings.ini? |
1 Attachment(s)
Originally Posted by Reverant
(Post 58402)
1) Where did you ground your LC-1? You absolutely need to ground it on the same location as the Megasquirt. Different points on the chassis will not do!
2) Can you post your MS .msq and MT settings.ini? settings.ini and msq attached :) |
Can you please put them in a .zip file? I don't have winrar on this pc and I don't intend to install one, thanks! :)
|
Originally Posted by Reverant
(Post 58435)
Can you please put them in a .zip file? I don't have winrar on this pc and I don't intend to install one, thanks! :)
no need I've sussed it, tho I'm not sure I want to admit what I'd done wrong.... :eek5: . . . . ah well, someone might learn from my miatake! I'd set the voltages the wrong way around in LM config. |
Ooops! Happy end though :)
|
All times are GMT -4. The time now is 07:33 PM. |
© 2024 MH Sub I, LLC dba Internet Brands