MS1, 10g, JimStim, no LEDs?
#1
Senior Member
Thread Starter
iTrader: (10)
Join Date: Apr 2007
Location: Ohio
Posts: 782
Total Cats: 4
MS1, 10g, JimStim, no LEDs?
So I'm sure I'm doing something wrong here. I hooked up the MS to my JimStim and everything looked good with Extra029y4. I flashed it with HR10g and I get no LEDs on the MS. Flash it back and it all looks fine again.
Also, the o2 values won't go over 12 in Tuner Studio. Seem to work fine in MT.
I've owned this damned thing for like 2 years and am just getting to where I need to install it. I fear it will be the biggest hurdle in the turbo project...
Also, the o2 values won't go over 12 in Tuner Studio. Seem to work fine in MT.
I've owned this damned thing for like 2 years and am just getting to where I need to install it. I fear it will be the biggest hurdle in the turbo project...
Last edited by soloracer; 04-24-2011 at 12:32 PM. Reason: spelling and emPHAsis
#3
Senior Member
Thread Starter
iTrader: (10)
Join Date: Apr 2007
Location: Ohio
Posts: 782
Total Cats: 4
OK, so that's not it....
I'd already installed the cap and just forgot that I did so. Help?
Should I maybe just forget TS and set the thing up with MT until I know it works right? Maybe the LEDs don't light with the spark when using high-res and I just missed that little fact somewhere???
I'd already installed the cap and just forgot that I did so. Help?
Should I maybe just forget TS and set the thing up with MT until I know it works right? Maybe the LEDs don't light with the spark when using high-res and I just missed that little fact somewhere???
#6
Senior Member
Thread Starter
iTrader: (10)
Join Date: Apr 2007
Location: Ohio
Posts: 782
Total Cats: 4
Do I need to use Easytherm to flash? I was just running the .bat files.
Brain - do your Easytherm values for Parallel 1.6 work OK for 1.8 too? I was using those.
Maybe I'll drag my MS, stim and netbook to ATL next week and pay somebody to school me.....any takers?
Brain - do your Easytherm values for Parallel 1.6 work OK for 1.8 too? I was using those.
Maybe I'll drag my MS, stim and netbook to ATL next week and pay somebody to school me.....any takers?
#10
Senior Member
Thread Starter
iTrader: (10)
Join Date: Apr 2007
Location: Ohio
Posts: 782
Total Cats: 4
No map. I think I have the dumb when loading stuff on this thing. Instructions from various sources and whatnot...
I was trying to do everything with bat files and Tuner Studio. I think I need to learn about Easy Therm and Megatune first, then use TS for autotune and fine tuning.
I suppose I could just forgo Hi-res for now. My plan is to only use MS1 briefly anyway, until I learn it, then upgrade to MS3 probably in the fall or next spring.
I was trying to do everything with bat files and Tuner Studio. I think I need to learn about Easy Therm and Megatune first, then use TS for autotune and fine tuning.
I suppose I could just forgo Hi-res for now. My plan is to only use MS1 briefly anyway, until I learn it, then upgrade to MS3 probably in the fall or next spring.
#12
Senior Member
Thread Starter
iTrader: (10)
Join Date: Apr 2007
Location: Ohio
Posts: 782
Total Cats: 4
Well, that would explain it. I assume it works with the 029y4 because you loaded a map for that when you built it.
I'm in GA now, maybe I'll take my MS to the track with me and see if someone at DIY will hold my hand...or I'll figure it out when I get back.
I'm in GA now, maybe I'll take my MS to the track with me and see if someone at DIY will hold my hand...or I'll figure it out when I get back.
Thread
Thread Starter
Forum
Replies
Last Post
StratoBlue1109
Miata parts for sale/trade
21
09-30-2018 01:09 PM
Mikel
MEGAsquirt
29
09-14-2015 09:11 AM