1990 turbo miata PARTOUT
 

But the car complete for $6500...or....

1.6l Built engine 337hp to the wheels on e85.


Millenium Motorsports Built engine
(Rebuilt stock head
ARP head studs
Manley rods
supertech pistons
boundary oil pump
ACL Race bearings)
(2500 miles on the engine).....PENDING

Begi intake manifold...PENDING

Artech Manifold and downpipe
Rebuilt 15g with a 19t cold side with oil lines, intercooler and piping
(2500 miles on turbo)...SOLD

Flyin Miata "Happy meal" clutch and lightweight flywheel....PENDING

3.9:1 torsen diff with housing axles and drive shaft.....800

Megasquirt Ms3x ecu with knock module and sensor, mapdaddy map sensor with second map,internal bluetooth, relayboard with cable, both diyautotune pigtails for the main and expansion boards.....SOLD

IGN-1 coil per plug (4 coils and igniters)....225

Flyin Miata BIG FUEL kit with fuel rail....400

Fiveomotorsports "black-ops" 1200cc injectors....PENDING

Ron Davis Racing radiator....SOLD

Momo steering wheel w/Dakei adapter....150

Bilstien Revalved shocks with ground control coilovers and eibach springs and ISC tophats......SOLD

Racing beat front and rear swaybars....100

Interested in the FM happy meal

Can you PM me since I cannot PM you due to post count

Have any other info on the ms3x? Did you just run timing off the CAS or did you also use a trigger wheel for your build?

Ms3x was running full sequential fuel and ignition, with knock, boost control, oil pressure input, table switch.......timing was run off of the cas.

**stupid question is stupid question**

I am interested in the intake, what throttle bodies are available and why would I want this manifold over a Honda manifold?

I was running the stock 1.6l tb. Setup made over 330whp. This manifold is from Begi, it books up to the head......as far as I know the Honda intake manifold requires some serious modification.

Hi Toby,

Where are you located?

Orange county, ca

Can u pm me a number, I can't pm you back

Pm'd.

I'll take these, what are the spring rates and lengths on the Eibachs?

"Bilstien Revalved shocks with ground control coilovers and eibach springs and ISC tophats......650"

I made 358 whp on a stock 1.6 intake and TB. Sooo, that may be a little more than I want to spend. I will buy a knock off Honda manifold for cheap. Thanks though.

Np

Is the radiator still available? Can you send me an email to sugup@bellsouth.net with condition and if it will fit a 97?
I don't have enough posts to pm.

Thanks.

Radiator sold
Ms3x sold

DANG a few hours too late, I wanted that ECU!

What type of adapter on the momo?

Sale pending on the whole car....

Sale didn't go through....buyer couldn't sell his car to pay for mine...

Tried to PM but your box is full.

Cleared out some room in my inbox....apologies

Dakei adaptor on the steering wheel.

How much is the rolling chassis worth?

Prices are obo

Whats the spring rate on the eibachs?

700/450

Pmed you

Some price drops....

item list updated

Updated the list

M-tuned reroute.........150

5speed trans, shift perfect......150

You don't happen to have a variable TPS lurking in there? Or is it going with the engine?

Sorry..outs going with the engine...

Reroute and sway bars .....pending sale

Hi i'm interested by your sterring Wheel, sway bar clutch/flywheel and intake manifold if it's not sold. reply me by mail alex_3357@hotmail.com Thanks

Also interesting in steering wheel plus adapted. Cant PM, too much noob :( Just need paypal!

Sorry. Steering wheel is sold. The rest are pending sales, except a 5 speed trans, a 3.9:1 torsen, and driveshaft. If things change I will update the thread. The pending sales should be picked up tomorrow night.

Interested in the RB front swaybar, which bar is it?

Im interested in the rear end, drive shaft, and axles. Whats the best you can do shipped to 77656?