6spd, Custom Turbo kit, KYB/FM, ACT 6puck, 9lb flywheel, 560cc RX7 Injectors etc...
This part out will be happening in the next couple weeks. So some flexibility will be required. Priority to locals for bigger items, please understand that shipping them is a chore and local makes life easier.
6spd Transmission - $500 It isn't perfect, but it was 100% fine for me to drive and track on. Reverse sometimes took a into first/2nd and then back to find. Otherwise, very happy with it. I've only added about 500 miles onto it and maybe 200 track miles. Was run with GM Syncromesh with friction modifier. XTD 9lb Cromoly flywheel - $150 (prefer to package with clutch) ACT HD 6puck sprung clutch - $200 Has a total of about 1500 miles on it. 500 with me. Clutch and Flywheel package for $300 Rx7 560cc Injectors. Cleaned before use in this car, have a few thousand miles since cleaning. They balanced out to less than 1% variance. PnP for miata. $150 Full Plug and Play Megasquirt - $350 Built by myself. Have been running it for the last 2 years. Is setup for HiRes codebase and has a capacitor to quell ignition hiccups. Includes an adapter harness that plugs into the OEM wiring. Wiring for a Nissan TPS is run off engine wiring harness if I remember right and IAT wiring is direct to ECU. IAT would be included. This is also setup to run fuel pump from in cabin wiring for simplicity. No pictures beyond this in car area picture, it is bolted to the passenger side of the lower console. http://i295.photobucket.com/albums/m...0014Medium.jpg Custom Intake manifold with TB - $400 Custom built aluminum intake manifold. CNC'd velocity stacks built into base of plenum. Larger body plenum for turbo cars. 6.5" runners as compromise between short/long and mid/high power bands. Uses factory fuel rail mounts and has provisions for vacuum fittings and IAT sensor underneath. Also uses stock throttle wire. This will also include a Nissan TB that is I believe 62mm? It has a variable TPS for people running aftermarket ECUs and wanting that option. Disclosure: It had cracked before and has since been rewelded and fully braced up. 3 lower underside braces and 2 braces up top. http://i295.photobucket.com/albums/m...IMG_0497-1.jpg http://i295.photobucket.com/albums/m...IMG_0518-1.jpg Custom 1.6L turbo setup based on a Garrett t3 .42/.48 - $500 I just recently finished building this kit. It is a stainless steel "upgraded" log manifold, with smoother transitions between 2 and 3. Turbo is setup to not stick straight off the manifold but at an uptilt. This is to prevent strain on the manifold studs/bolts and prevent fastener failure. It is setup for external wastegate and for a little more money a Tial wastegate can be included. For even smaller money, a knockoff tial (that works fine) can be included. The external wastegate is routed into the downpipe. The turbine housing has been modified with a 3" vband directly off of it and the downpipe is thus a full 3" all the way down to the exhaust flange. The downpipe is a mix of stainless and mild steel. It has an o2 bung already welded into an easy to reach location that is perfectly vertical. I also have a support structure that uses a heim joint at the turbo to support its weight, another format to avoid failures down the road. Parts in this package: Custom Stainless manifold Modified T3 .48 housing (3" vband exit) 3" vband downpipe with external wastegate routing Fresh Rebuild, 0 mile, Garrett T3 .42/.48 - $225 Optional Tial 38mm - $150 Optional SSautochrome Tial knockoff - $70 Optional 3" flex section for exhaust or into downpipe - part cost + some labor for cutting/welding Optional Oilpan modded for drain - Included if big package bought (inj/wg/kit) Oil feed and oil drain line - Included if big package bought (inj/wg/kit) http://i295.photobucket.com/albums/m...s/8f3995d0.jpg http://i295.photobucket.com/albums/m...s/36bcce9f.jpg http://i295.photobucket.com/albums/m...s/530e3535.jpg http://i295.photobucket.com/albums/m...e/adbe716c.jpg http://i295.photobucket.com/albums/m...e/e9891b65.jpg Buy entire KIT/Turbo/WG/get freebies for $800. KYB AGX with FM springs preassembled with NA tophats (20k miles) - $250 http://i295.photobucket.com/albums/m...e/f8510b76.jpg http://i295.photobucket.com/albums/m...e/06dc93cb.jpg 2001 Torsen Swap with one piece axles/driveshaft - $700 1.6l 5spd from my 93, has 95k on it - $200 splitime@gmail.com and PM here is the best way to reach me. I'll try to answer any and all questions. Please remember to be flexible if you want these parts. I have to pull the car apart first... and I won't be starting for at a week or so, especially for bigger stuff like trans/clutch/flywheel. V-mount also available... but buyer needs to chat with me. As it takes some welding work. It is NOT a bolt in solution, except for the rear mount. |
man i wish i could fit that intake under my hood =(, the cluitch and fly wheel are for a 1.6 right?
|
Originally Posted by Hot_Wheels
(Post 613586)
man i wish i could fit that intake under my hood =(, the cluitch and fly wheel are for a 1.6 right?
We could test fit it, hood clearance wouldn't be issue... but It would aim into firewall/shocktower for you I bet. |
And for those that care... I'm not selling the car, I'm not going anywhere, I'm not doing a v8 swap. Something fun is up my sleeve though.
|
I care.
Let me know on the last week of the month if you still have the trans. I have the week off (road triiiiip) |
Originally Posted by Splitime
(Post 613589)
And for those that care... I'm not selling the car, I'm not going anywhere, I'm not doing a v8 swap. Something fun is up my sleeve though.
|
Originally Posted by shlammed
(Post 613597)
I care.
Let me know on the last week of the month if you still have the trans. I have the week off (road triiiiip) |
Intake is for a 1.6?
|
Originally Posted by faeflora
(Post 613625)
Intake is for a 1.6?
|
Originally Posted by Splitime
(Post 613589)
And for those that care... I'm not selling the car, I'm not going anywhere, I'm not doing a v8 swap. Something fun is up my sleeve though.
At first I was like :eek: No way! .... then I was like :eek: holy shit I can wait to see this lol. Quickly what are you going with? GLWS |
Originally Posted by Splitime
(Post 613589)
And for those that care... I'm not selling the car, I'm not going anywhere, I'm not doing a v8 swap. Something fun is up my sleeve though.
Pm price for Ewg shipped to 07310 GL with v8 swap....will be subscribing to that build! |
Originally Posted by TonyV
(Post 613636)
We all care, as I'm sure everyone saw Splitime + Part Out = :crx:
Pm price for Ewg shipped to 07310 GL with v8 swap....will be subscribing to that build! And no v8 swap! :p |
Om nom nom nom
|
can i get pics of the flywheel please.. very intertested...
|
Do you have pics of the injectors? I'm interested
|
Sent PM about the 6speed
|
Thanks for the cops bro, also, can you route the intercooler piping in the normal fashion for a FMIC with the TB being off-set like it is on your intake manifold, I may be interested and just sell my flipside mani
|
Originally Posted by mazda311
(Post 613816)
Do you have pics of the injectors? I'm interested
Originally Posted by DriftProjectR
(Post 613810)
can i get pics of the flywheel please.. very intertested...
Originally Posted by jtothawhat
(Post 613840)
Thanks for the cops bro, also, can you route the intercooler piping in the normal fashion for a FMIC with the TB being off-set like it is on your intake manifold, I may be interested and just sell my flipside mani
Does this top downish picture with no headlight lid help? http://i295.photobucket.com/albums/m...s/IMG_0581.jpg Inside the manifold bling http://i295.photobucket.com/albums/m...s/IMG_0485.jpg |
Pming u for the torsen.
|
Pming u for the torsen.
|
All times are GMT -4. The time now is 03:45 PM. |
© 2024 MH Sub I, LLC dba Internet Brands