BEGI Kit Part Out - Downpipe, Intercooler, TSE Inconel Stud Kit, Injectors, Aero
03-19-2015, 11:16 PM
#1
Junior Member
Thread Starter
iTrader: (2)
Join Date: Apr 2013
Location: Louisville, KY
Posts: 49
Total Cats: 0
BEGI Kit Part Out - Downpipe, Intercooler, TSE Inconel Stud Kit, Injectors, Aero
I have the following up for sale. Nothing wrong with the parts; I have just decided that I don't feel like doing all of the supporting modifications to add boost to my track car. Comments are made where necessary. Willing to make a deal on everything if you want.
All parts are for an NA with a 1.8L unless otherwise noted. Located in Louisville, KY. Prices do not include shipping.
All parts are for an NA with a 1.8L unless otherwise noted. Located in Louisville, KY. Prices do not include shipping.
RC 550cc Injectors with Clips - Labeled as "SL9-550". These injectors are in good condition, but will require a new set of o-rings to install. Visually, they look great, but I have not tested them. High impedance. Flow match documents and original purchase documents included. $250BEGI Turbo Intake - Has a 2.25" 90 deg coupler and a 135 deg hard pipe with a crankcase vent hose connection. Includes a 5" long K&N filter. Bring your own clamps as necessary. $100BEGI 1.8L Turbo Manifold with T2 flange. Mates up to a T28 or T25 frame turbo. Has an EGR port on it. You'll need your own cap for it as it is currently open. In great condition. Hard to break these. Best manifold on the market in my opinion. $300- Turbosmart Manual Boost Controller - WYSIWYG $75
- BEGI Intercooler with Hot Side Piping - Intercooler is coated in some sort of black coating. Looks pretty nice and I imagine it would look good in your grill opening. Includes the hot side piping for a turbo that is clocked downward with a 2" OD outlet. Piping steps from 2" to 2.25". Piping was coated with a black wrinkle coating at one point. It was flaking so I scraped off what would come off and then put some satin black Krylon on it to gussy it up. If you're not trying to build a show car, you probably won't care. If you are, move on. Bring your own cold side piping. $400 for all of it. Kit is $1000 new, so add $75 worth of couplers and cold side piping and OMFG, that's a good deal.
BEGI T25 Downpipe - Made for an internally gated T25 mounted to a BEGI manifold. Starts at 2.25" OD and ends at 2.5" OD. Appears to be mild steel. Has 2 O2 bungs in it. One of them is open and one has a plug. Length is slightly adjustable with the slip joint. $225BEGI T25/T28 Churbo Chinacharger with Stainless Lines - Fast spool of a T25 with good flow of a T28. Best of both worlds. Has some minor side to side and axial play, but without oil on the center section, it's tough to judge. I can't imagine there would be any problem, but you might try rebuilding it just to be safe. Has a baffled exhaust setup to prevent mixing of turbo and wastegate gases. The lines are all very nice stainless lines with high-end fittings. Only problem I can find with it is one of the studs appears to have been sheared off during install/unistall. Stud can be drilled out and re-tapped... or heck, you could probably even run without it if you had a fresh gasket. $250 for the whole shebang. Rebuild it for $70 and have a new turbo with ballin lines for less than the cost of a new turbo alone.Trackspeed Engineering (TSE) Inconel Stud Kit - Brand spankin' new. Protect your track car from breakdowns on the third lap. These are $155 new.SOLD- ISC Racing Front Air Dam - Fiberglass front air dam from ISC Racing. See the ISC Racing site for details (Miata Air dam). Currently unused in black gel coat. Very nice piece with fantastic aero perks. $175
- Kinetic Sunbelt 1.6L Spec Miata Engine - Makes fantastic power for a 1.6L. Dyno'd around 113 whp on a NASA dyno after a race in SM form. Made 123 whp with ITBs. Has roughly 6 racing seasons on it. Comes with a tuned AFM. Leaks oil out of the cam seal area. $500
- Purple 260cc NB Injectors - I have 2 sets of these. $50 per set.
- VTCS NB Intake Manifold - Butterfly plates are removed, but the shaft is still there. $50
- OEM '01 Flywheel - If you're converting from a 1.6L to a 1.8L clutch, here's a cheap way to make that upgrade happen. Has some spots on it, but I'm sure it will clean up with some 400 grit. $25
- 1.8L Throttle Body - Came from a flat-top manifold... so you know it's good. $23
Last edited by Mistamike17; 03-25-2015 at 06:53 AM.
Reply
1
1
Thread
Thread Starter
Forum
Replies
Last Post
Rudes333
Miata parts for sale/trade
17
11-05-2015 01:16 PM
