LOTS OF TURBO PARTS (Begi, ARTech, Supertech, RC and TiAL)
#1
LOTS OF TURBO PARTS (Begi, ARTech, Supertech, RC and TiAL)
ALL PARTS are off a 1.8 NA (1997)
Ok so I have some things laying around, need them gone. JUST OFFER, reasonable offers wont be refused!
Located: SoCal, 91754
contact: 714 369 5952
-Joshua
-Toda Oil pump gear Brand New- $250obo
-HKS Hypermax II (under 2k miles)- $1,000obo **PENDING FOR $650 + $200 value part trade
-3" TiAL v-band down pipe (1.2k miles side mount and bottem mount ok)- $150obo PENDING for $100
-Stock exhaust with a tanabe axle back (on car when purchased at 112k miles)- $50obo
-T3/T4 China charger .63ar Brand New!- $175obo shipped *EDITED T28 is gone
"Intake: 3 inch
Inlet: 2 inch
Compressor trim: .50
Compressor Wheel diameter: 50.16 / 76.84
Turbine Wheel diameter: 54.06 / 65.20
Exhaust Trim: .63ar
Turbine flange type : T3 flange
Down pipe flange type: 5 bolt standard
Cooling type: oil cool only
Horsepower rating: 350+"
http://www.ebay.com/itm/GODSPEED-T04...ht_3139wt_1185
-RC550cc New w/pigtails (I can't find flow charts)- $300obo
-Couplings (90, and 45 degree different sizes)- $2.50 ea.
-IC piping (stright pipe 3")- $15
-1.8 NA Intake Mani stock(112k miles, CLEAN)- $90obo
added:
-bunch of claps various sizes- $1 ea.
-52mm gauge pod (mounts on dash/ wheel hub cover/ gauge hood)- $5
-52mm radio delete gauge pod- $10
-1.8 bare stock intake manifold (off an 97 NA8)- $100 obo
Coilovers
RCs
Toda
Stock exhaust
Stock intake mani
SOLD:
China charger T28- $100 SOLD for $100 shipped
Begi turbo heat shield- $80obo SOLD for 73.50 shipped!
AutoMeter Air/Fuel gauge (unknown usage, I never installed it)- $20obo SOLD FOR $35 shipped
3" ARTech v-band Mid pipe (unknown miles, CLEAN with flex pipe, and bundge)- $150obo SOLD FOR $130 SHIPPED
Supertech OverSized Valvetrain (1.2k milescomplete)- $225obo **SOLD FOR $300 shipped
part# RET-TS60/MA2 & SEAT-TS/MA181 (valves)
SPRK-MM18S-K (Springs)
RET-TS60MA2 (Retainers)
Ok so I have some things laying around, need them gone. JUST OFFER, reasonable offers wont be refused!
Located: SoCal, 91754
contact: 714 369 5952
-Joshua
-Toda Oil pump gear Brand New- $250obo
-HKS Hypermax II (under 2k miles)- $1,000obo **PENDING FOR $650 + $200 value part trade
-3" TiAL v-band down pipe (1.2k miles side mount and bottem mount ok)- $150obo PENDING for $100
-Stock exhaust with a tanabe axle back (on car when purchased at 112k miles)- $50obo
-T3/T4 China charger .63ar Brand New!- $175obo shipped *EDITED T28 is gone
"Intake: 3 inch
Inlet: 2 inch
Compressor trim: .50
Compressor Wheel diameter: 50.16 / 76.84
Turbine Wheel diameter: 54.06 / 65.20
Exhaust Trim: .63ar
Turbine flange type : T3 flange
Down pipe flange type: 5 bolt standard
Cooling type: oil cool only
Horsepower rating: 350+"
http://www.ebay.com/itm/GODSPEED-T04...ht_3139wt_1185
-RC550cc New w/pigtails (I can't find flow charts)- $300obo
-Couplings (90, and 45 degree different sizes)- $2.50 ea.
-IC piping (stright pipe 3")- $15
-1.8 NA Intake Mani stock(112k miles, CLEAN)- $90obo
added:
-bunch of claps various sizes- $1 ea.
-52mm gauge pod (mounts on dash/ wheel hub cover/ gauge hood)- $5
-52mm radio delete gauge pod- $10
-1.8 bare stock intake manifold (off an 97 NA8)- $100 obo
Coilovers
RCs
Toda
Stock exhaust
Stock intake mani
SOLD:
China charger T28- $100 SOLD for $100 shipped
Begi turbo heat shield- $80obo SOLD for 73.50 shipped!
AutoMeter Air/Fuel gauge (unknown usage, I never installed it)- $20obo SOLD FOR $35 shipped
3" ARTech v-band Mid pipe (unknown miles, CLEAN with flex pipe, and bundge)- $150obo SOLD FOR $130 SHIPPED
Supertech OverSized Valvetrain (1.2k milescomplete)- $225obo **SOLD FOR $300 shipped
part# RET-TS60/MA2 & SEAT-TS/MA181 (valves)
SPRK-MM18S-K (Springs)
RET-TS60MA2 (Retainers)
Last edited by jOshiro33; 02-16-2012 at 10:42 PM.
#12
that is the flange, I had the ARTtech DP (but it was damaged from storage so I cut off the flange so it can be attached to the new down pipe)
The heat shield is not from a kit I just bought it.
http://www.bellengineering.net/produ...roducts_id=432
GOING TO THE POST OFFICE NOW!
The heat shield is not from a kit I just bought it.
http://www.bellengineering.net/produ...roducts_id=432
GOING TO THE POST OFFICE NOW!