BEGI SGDP with a 3" rear section w/flex pipe
#1
Senior Member
Thread Starter
iTrader: (2)
Join Date: Sep 2009
Location: Edmonton, AB, Canada
Posts: 1,193
Total Cats: 29
BEGI SGDP with a 3" rear section w/flex pipe
BEGI Downpipe from a 2002 car
I have for sale a used Mild Steel BEGI separated gas turbo downpipe. The rear is a custom 3" tubing (only parts that is stainless) with a flex pipe and a 3 bolt flange. Had a bung welded in the 3" section for my Uego
Good condition and ready to install.
Asking $260 plus shipping. We can split shipping.
*** I may be willing to sell my full 3" exhaust that was mated to this with the giant 22" Magnaflow. Done locally at ABC muffler after I provided them with the mandrels and flex pipe. It has no cat, is partial steel and stainless, mandrel on the tight curves and a exhaust shop bend on the slight angles along the PPF and a nice stainless 4" tip. *** pickup/meet only in Alberta/BC
I have for sale a used Mild Steel BEGI separated gas turbo downpipe. The rear is a custom 3" tubing (only parts that is stainless) with a flex pipe and a 3 bolt flange. Had a bung welded in the 3" section for my Uego
Good condition and ready to install.
Asking $260 plus shipping. We can split shipping.
*** I may be willing to sell my full 3" exhaust that was mated to this with the giant 22" Magnaflow. Done locally at ABC muffler after I provided them with the mandrels and flex pipe. It has no cat, is partial steel and stainless, mandrel on the tight curves and a exhaust shop bend on the slight angles along the PPF and a nice stainless 4" tip. *** pickup/meet only in Alberta/BC
Last edited by Landrew; 04-16-2014 at 04:24 PM.
#6
Senior Member
Thread Starter
iTrader: (2)
Join Date: Sep 2009
Location: Edmonton, AB, Canada
Posts: 1,193
Total Cats: 29
I don't know enough about that to tell you either way though I suspect the NA/B differences happen post DP.
Sorry if you meant the addition of the 3" section then I doubt it. If your buying this then you should get the rest custom made in 3" and add the giant Magnaflow. Most shops can handle that.
Sorry if you meant the addition of the 3" section then I doubt it. If your buying this then you should get the rest custom made in 3" and add the giant Magnaflow. Most shops can handle that.
Last edited by Landrew; 04-16-2014 at 04:45 PM.
#10
Senior Member
Thread Starter
iTrader: (2)
Join Date: Sep 2009
Location: Edmonton, AB, Canada
Posts: 1,193
Total Cats: 29
Goodbye Apple phone, hello Note 3.
Better pics, same price.
*** Remember I also will be cutting off the other side of the flange (that is not pictured) at a spot few inches into the 3" tubing and you will be getting that as well. What this means is all you have to do is get someone to weld the tubing to your current setup. You will have both 3 bolt flange sides so you don't have to hassle with thatt. ****
I just need to rent the big 3" exhaust cutter to make a nice smooth cut.
Better pics, same price.
*** Remember I also will be cutting off the other side of the flange (that is not pictured) at a spot few inches into the 3" tubing and you will be getting that as well. What this means is all you have to do is get someone to weld the tubing to your current setup. You will have both 3 bolt flange sides so you don't have to hassle with thatt. ****
I just need to rent the big 3" exhaust cutter to make a nice smooth cut.
Thread
Thread Starter
Forum
Replies
Last Post