Turbo part out/ feeler
10-11-2010, 10:31 AM
#1
Junior Member
Thread Starter
iTrader: (1)
Join Date: Apr 2009
Location: illinois
Posts: 183
Total Cats: -4
Turbo part out/ feeler
I am thinkin of selling my miata drivetrain. Ill start my way from the back. the rear end can go. its factory with around 115k miles on it. factory driveshaft . rebuilt transmission with clutchmasters stg 2 clutch and pressure plate throwout bearing and pilot bearing replaced during rebuild. For the motor it has been completely rebuilt by a shop. the block and head has been decked. All cylinders were honed for deglazing (stock bore). It has a valve job on it along with port and polished head. Felpro gasket kit both upper and lower conversion set. Acl race main bearings. micropolished crank. Eagle forged H beam connecting rods along with Cp forged 9.0 : 1 pistons. New timing belt. NO powersteering or ac. For turbo componenents i have a jgs i believe? log style manifold.. (do it yourself and weld a manifold together deals) the turbo is a china charger turbo made by emotor. it is a e-motor gt2860. All the necessary plumbing for oil and water cooled turbo. A coolant reroute from the back of the cylinder head to the radiator. . . Intercooler piping and front mount intercooler. greddy ssqv blowoff valve. deatchsworks 600 cc injectors adaptronic ecu e420c with a 3 bar map from travis at Boundary Engineering. Lc1 wide band o2 sensor with digital blue guage. Street glow boost guage. apexi turbo timer. 2.5 inch downpipe. and i believe that is about it.. i may have missed some things on here i will go through it later if i did. It would be ideal to sell all this all at once or atleast if someone buys all the turbo goodies . and someone buy the motor. I will not dismantle the motor and part it out. but this is just a feeler also to see what people on the boards think its all worth to sell. all these parts have less than 1000 miles on them. Sadly i havent got the time or the funds to get the tune finshed.
Reply
0
0
10-11-2010, 10:13 PM
#5
Junior Member
Thread Starter
iTrader: (1)
Join Date: Apr 2009
Location: illinois
Posts: 183
Total Cats: -4
Idealy i was thinking somewhere around the price of 2500 plus or minus a couple hundred depending on if exhaust manifold were to be included plus shipping cost... its definatly not a set price. I just gotta take some time to scavenge the forums to see what others have previously asked for long blocks. It is however a fairly new rebuild. And i have receiepts somewhere.
Reply
0
0
10-13-2010, 11:15 AM
#11
Junior Member
Thread Starter
iTrader: (1)
Join Date: Apr 2009
Location: illinois
Posts: 183
Total Cats: -4
Transmission - cleaned and rebuilt with stage two clutchmasters clutch and pressure plate including driveshaft ............ $1,500 plus shipping
Long block - forged cp 9.0:1, eagle h beam, acl race bearings, port n polished head. valve job, fel pro gasket kit, honed, stock bore, head and block decked............ $2500 plus shipping. (motor mounts included)
k-member (engine cradle)................. $300.00 plus shipping
rear end (stock gearing) ................. $400.00 plus shipping
LC1 innovative wide band with sensor and blue guage (lc1 box slightly melted but still functions properly) .................... $150.00 plus shipping
Street glow boost guage ..................... $50.00 shipped
Adaptronic e420c complete ecu with deatchsworks 600 cc injectors, 3 bar map, and gm IAT sensor ............................ $1375.00 plus shipping
E-motor gt2860 turbo with coolant and oil lines and extra turbo with bad chra and fins
............................. $600.00 shipped (if gjs manifold and 2.5'' downpipe want to be inclueded) .... $900.00 shipped
FMIC and 2.5'' intercooler pipes along with couplings .......................... $450.00 plus shipping
oil catch can with hoses and fitting...................... $55.00 plus shipping
I have gone through my mailbox so people can pm me. I'm sure to some these prices may be high. I don't really have anything to base it off of aside from what I have personally spent and marked quite a bit off on most of the items. Please keep in mind most of these items are in fairly new condition as i have not been able to get my car properly tuned so it just sits in the garage.
Long block - forged cp 9.0:1, eagle h beam, acl race bearings, port n polished head. valve job, fel pro gasket kit, honed, stock bore, head and block decked............ $2500 plus shipping. (motor mounts included)
k-member (engine cradle)................. $300.00 plus shipping
rear end (stock gearing) ................. $400.00 plus shipping
LC1 innovative wide band with sensor and blue guage (lc1 box slightly melted but still functions properly) .................... $150.00 plus shipping
Street glow boost guage ..................... $50.00 shipped
Adaptronic e420c complete ecu with deatchsworks 600 cc injectors, 3 bar map, and gm IAT sensor ............................ $1375.00 plus shipping
E-motor gt2860 turbo with coolant and oil lines and extra turbo with bad chra and fins
............................. $600.00 shipped (if gjs manifold and 2.5'' downpipe want to be inclueded) .... $900.00 shipped
FMIC and 2.5'' intercooler pipes along with couplings .......................... $450.00 plus shipping
oil catch can with hoses and fitting...................... $55.00 plus shipping
I have gone through my mailbox so people can pm me. I'm sure to some these prices may be high. I don't really have anything to base it off of aside from what I have personally spent and marked quite a bit off on most of the items. Please keep in mind most of these items are in fairly new condition as i have not been able to get my car properly tuned so it just sits in the garage.
Reply
0
0
10-15-2010, 10:06 PM
#15
Need more info on that motor. God that would simplify my life right now. What is in it for valve train? I.E.
-Aftermarket valves or OEM?
-Oversized?
-Valvesprings?
-Viton seals?
What year is the block and head? I assume 99/00? Just checking?
Any Oil pump gears or Harmonic balancer?
Motor's mileage, and mileage after rebuild?
Also, super important, please get a Compression check and leakdown test and post numbers, that would be really really beneficial. Thanks.
Is that tranny a 6-speed? Mileage? How are the shifts?
-Aftermarket valves or OEM?
-Oversized?
-Valvesprings?
-Viton seals?
What year is the block and head? I assume 99/00? Just checking?
Any Oil pump gears or Harmonic balancer?
Motor's mileage, and mileage after rebuild?
Also, super important, please get a Compression check and leakdown test and post numbers, that would be really really beneficial. Thanks.
Is that tranny a 6-speed? Mileage? How are the shifts?
Reply
0
0
10-16-2010, 04:39 AM
#16
Junior Member
Thread Starter
iTrader: (1)
Join Date: Apr 2009
Location: illinois
Posts: 183
Total Cats: -4
Chance and crazy drummer. I will be answering these questions real soon. please let me pull some specs and numbers for you both. Sorry in advance for any delays
Reply
0
0
10-20-2010, 11:11 AM
#17
Junior Member
Thread Starter
iTrader: (1)
Join Date: Apr 2009
Location: illinois
Posts: 183
Total Cats: -4
LC1 and turbo timer are now sold. I would also consider selling the whole drive train, everthing i have left for sale, all together for 5,300. Local pick up only.
Reply
0
0
