Turbo track car part out, lots of good parts in here!
 

I am going to start parting out my turbo track car so I can move on to another project.
Below is a list of some of the items that are on the block, I will add more when they come up since I'm sure I have forgotten a few things.
The car is currently still in one piece so please be patient with timeframes on certain parts. I will be up front about when I can get to certain pieces of the car. Please check my feedback and feel free to contact anybody I have done business with here, I am a stand up guy.

Prices are OBO they do not include shipping. Please add 3.5% if you wish to use Paypal.
My zip is 30518 if you want to get an idea of what shipping would cost you.

95 1.8 $2200
Less than 500 miles since the build. The machine work and assembly was done by NOMSG and Balanced Performance did the tune once it was completed. The motor was broken in properly with 30 wt oil and no boost. Here is a short list of the specs and parts.
-8.8:1 compression ratio
-ARP head, main cap, and connecting rod bolts.
-M-Tuned rods
-Clevite bearings
-Cylinder head and Manifold are port matched
-Coolant reroute
-Oil pan has 10an fitting welded on for the turbo's oil return
-I have a 99 head and manifold that could be thrown in as a sweetener.

Turbo kit $2200
-Begi manifold and downpipe
-Trackspeed Engineering Inconel stud kit
-Garrett GT2871R
-stainless braided oil lines
-550cc Denso RX-7 injectors
-Turbosmart BOV
-AEM wideband
-Intercooler
-Hot and cold side pipes with all silicone connectors and t-bolt clamps

Rolling chassis with roll cage $1500
This would make a great start for a chump or Lemons car, The cage was built using NASA guidelines for a 2501-3000lb car.

DIYPNP 90-93 $400

Trackspeed Engineering Toyota Cops (wired for a 1.8 swapped into a 90-93) Sold

Walbro 190HP fuel pump $65

3in Enthuza Dual exhaust Sold

ACT Extreme 6-puck clutch and pressure plate for the 1.6 (can be used on the 1.8 with a 1.6 flywheel) $250

99 5-speed $250

4.1 Torsen swap w/ axles and driveshaft included (I currently have two complete swaps) $500 ea

Tein Flex w/10k front and 6k rear springs Pending

Racing Beat tubular front sway bar and adjustable rear $old

Racing beat adjustable sway bar end links $80

Racing beat sway bar brace $50

FM Cannon brace Sold

1.8 brakes with nearly new Hawk DTC-60 pads $300

Corbeau Forza seat (some wear) $150

(2) Sparco 5-point cam lock harnesses in fantastic shape, dates are expired $100 / set

Momo Monte Carlo steering wheel Sold

NRG quick release Gen 2 w/ short hub Sold

Lexan pop out vent windows (fits 90-05) Sold

Convex mirror $30

https://www.miataturbo.net/attachmen...ine=1344475688

https://www.miataturbo.net/attachmen...ine=1344475688

https://www.miataturbo.net/attachmen...ine=1344475688

pm'd... I NEED that DIYPNP :)))

pmed about torsen set up and sways

pm'd

Momo Steering Wheel
 

350 mm or 320?

I believe it is tree-fiddy. 13.5 inches across.

you aware brah?

Interested in:

DIYPNP (I have the same setup as you, 1.8 into 90-93 chassis)
Momo steering wheel
AEM wideband w/ gauge? (If you want to part the turbo kit)

Still available?

Interested in the quick release & short hub. I sent you an email to your gmail account.

DIYPNP still available, Momo has been sold. I really want to sell the kit whole but I'll put you on the list for the AEM if I have to part it.

are you interested in selling the 99 head?
only interested if it's stock

Rolling chassis include the 6uls?

I'm gonna say no since I'm picking the 6UL's up hopefully tomorrow. :)

Sure doesn't, however it will include a sweet stock set of wheels and tires to get it on a trailer.

Thanks. I have a car, but need some 9" 6uls. I bought a hard top once that came with a free Miata so I thought I would ask. :giggle:

email me at rneerpat at gmail dot com....can't pm yet. definitely interested

interested in the cannon brace. how much shipped to 43068? Also do you happen to have any strut braces.

I'd like to buy the front RB sway bar. Anyone want the rear? Separate it?

I'm also interested in the front rb sway bar if ^ doesn't want it.

Sorry, I'm not going to separate them.