1.8L Built Belfab HP - 95 block/99 head and BEGI turbo/mani/down
08-30-2009, 07:38 PM
#1
Senior Member
Thread Starter
iTrader: (21)
Join Date: May 2008
Location: San Antonio
Posts: 733
Total Cats: 17
1.8L Built Belfab HP - 95 block/99 head and BEGI turbo/mani/down
This is the one the infamous chucky had built. I just retired my race car nad I need a replacement so my miata is getting turning into a spec miata. This thing is still ont he stand and I definitely can't use for SM.
$2200
...it has $2500 in parts and machine work + cost of donor 99 head and 95 block. ARP fasteners etc...oversized valves (29/34 nitrided), 9.0:1 84mm bore
I also have ZXTex's previous BEGI GT2560 turbo/ cast manifold/stainless downpipe for sale @ $1300, I don't think he had more than 1k miles on it if that. I'll check with him tomorrow on that.
Can deliver to any major Texas metro area.
Thanks,
Ryan
$2200
...it has $2500 in parts and machine work + cost of donor 99 head and 95 block. ARP fasteners etc...oversized valves (29/34 nitrided), 9.0:1 84mm bore
I also have ZXTex's previous BEGI GT2560 turbo/ cast manifold/stainless downpipe for sale @ $1300, I don't think he had more than 1k miles on it if that. I'll check with him tomorrow on that.
Can deliver to any major Texas metro area.
Thanks,
Ryan
Last edited by rlogan; 08-31-2009 at 09:06 PM.
Reply
0
0
08-30-2009, 11:54 PM
#3
Senior Member
Thread Starter
iTrader: (21)
Join Date: May 2008
Location: San Antonio
Posts: 733
Total Cats: 17
It was on an NB, you can have oil lines and coolant lines with it....I am pretty sure this setup would work with either. His car was a 99 and the original car this was to go into was a 94.
Reply
0
0
08-31-2009, 02:56 AM
#4
Former Vendor
iTrader: (31)
Join Date: Nov 2006
Location: Sunnyvale, CA
Posts: 15,442
Total Cats: 2,099
If those are low-comp Supertechs, you supposedly cannot obtain those pistons anymore. Buy the motor and join the low-comp gentleman's club. (plus, how badass of a story is "yeah, the OP of this motor is up on murder charges lol")
Reply
0
0
08-31-2009, 10:47 AM
#6
Senior Member
Thread Starter
iTrader: (21)
Join Date: May 2008
Location: San Antonio
Posts: 733
Total Cats: 17
I'll make pdfs of the receipts tonight...yes, it was very weird going to pick that motor up! 
Motor is still on stand, never been run. Pics of all parts will be up tonight.
Motor is still on stand, never been run. Pics of all parts will be up tonight.
Reply
0
0
08-31-2009, 11:49 AM
#9
Senior Member
Thread Starter
iTrader: (21)
Join Date: May 2008
Location: San Antonio
Posts: 733
Total Cats: 17
I would consider shipping...not my first choice, but we could crate it.
Layaway, hmm...how much down? I am not in need of the money so it's not out of the question. And only because I've met you.
Layaway, hmm...how much down? I am not in need of the money so it's not out of the question. And only because I've met you.
Reply
0
0
08-31-2009, 10:32 PM
#11
Senior Member
Thread Starter
iTrader: (21)
Join Date: May 2008
Location: San Antonio
Posts: 733
Total Cats: 17
It is 9.0:1, I apologize....receipts here and engine pics in this album
For Sale pictures from sports photos on webshots
For Sale pictures from sports photos on webshots
Reply
0
0
09-18-2009, 11:12 AM
#14
Senior Member
Thread Starter
iTrader: (21)
Join Date: May 2008
Location: San Antonio
Posts: 733
Total Cats: 17
BEGI GT2560 turbo/ cast manifold/stainless downpipe is GONE!
Motor still sitting here...but if my race car sells...I may end up putting it in a car after all.
Motor still sitting here...but if my race car sells...I may end up putting it in a car after all.
Reply
0
0
09-18-2009, 11:22 AM
#15
Elite Member
iTrader: (15)
Join Date: Dec 2007
Location: San Antonio, Texas
Posts: 4,847
Total Cats: 27
Putting in a good word for Ryan. Buy from him with confidence. This is a smoking deal for this motor. I cannot believe he is selling it. If I did not already have a built motor I would be all over it.
Reply
0
0
Thread
Thread Starter
Forum
Replies
Last Post
StratoBlue1109
Miata parts for sale/trade
21
09-30-2018 01:09 PM
