MSPNP2 - Updated to 3.3.0 open the basemap .msq
#1
MSPNP2 - Updated to 3.3.0 open the basemap .msq
First off I would like to say Finally i got around to installing my Mega in the miata.
My issue is that I updated to the latest firmware using the instruction posted on Megasquirt MS2/Extra Loading firmware and Upgrade Notes but the basemap will not load.
I followed the instructions for upgrading and I was successful in upgrading to 3.3.0.
I created a project, gave it a name etc. I go to open the basemap MS2E v3.3.0 MSPNP2-MM9093 and i get a couple of errors.
the first one is : Signatures do not match!
Tune File signature: null
Configuration Signature: MS2Extra comms330MP
do I want to load anyways? I say "Yes" then i get a prompt stating that it will load settings from the 1 1992 Miata.msq and current tune.msq will be updated with the new setting. Click "Yes" to proceed
I then get this message: Error opening Saved tune.
Reported Error:
Problem parsing tune settings file (.msq):
The markup in the document following the root element must be well-formed.
Root problem: The markup in the document following the root element must be well-formed.
So, has anyone had this issue, is there a known good basemap that I can download from an alternate location?
When i get home, im going to re-flash frimware 3.3.0 on my MS and try to load the tune again.
My issue is that I updated to the latest firmware using the instruction posted on Megasquirt MS2/Extra Loading firmware and Upgrade Notes but the basemap will not load.
I followed the instructions for upgrading and I was successful in upgrading to 3.3.0.
I created a project, gave it a name etc. I go to open the basemap MS2E v3.3.0 MSPNP2-MM9093 and i get a couple of errors.
the first one is : Signatures do not match!
Tune File signature: null
Configuration Signature: MS2Extra comms330MP
do I want to load anyways? I say "Yes" then i get a prompt stating that it will load settings from the 1 1992 Miata.msq and current tune.msq will be updated with the new setting. Click "Yes" to proceed
I then get this message: Error opening Saved tune.
Reported Error:
Problem parsing tune settings file (.msq):
The markup in the document following the root element must be well-formed.
Root problem: The markup in the document following the root element must be well-formed.
So, has anyone had this issue, is there a known good basemap that I can download from an alternate location?
When i get home, im going to re-flash frimware 3.3.0 on my MS and try to load the tune again.
#3
It was my first time updating, and I never opened the case to see if the jumper was on or not.
When I launched tuner studio afterwards, it detected my mega. it had it listed as 330d from the ini file.
im also using a usb to serial adapter for the MS, but i dont think this is an issue.
I forgot to mention that I used the default debug when flashing the update. However, the firmware flash didnt fail, or didnt notify me that it did. Should I try to flash without the Boot Jumper?
When I launched tuner studio afterwards, it detected my mega. it had it listed as 330d from the ini file.
im also using a usb to serial adapter for the MS, but i dont think this is an issue.
I forgot to mention that I used the default debug when flashing the update. However, the firmware flash didnt fail, or didnt notify me that it did. Should I try to flash without the Boot Jumper?
Last edited by zero415; 12-02-2013 at 04:22 PM.
#4
Update:
I downloaded the 3.3.0 flash and I used the boot jumper and followed all the on screen instructions from the command prompt. it seems to flash normal and doesnt give any other messages.
When I go to open the 3.3.0 base file the window says unrecognized file. and still gives the null error.
My next question is does anyone have the MS2/Extra pre-3.3 beta 16.20130822 firmware that I could have?
Update 2:
nevermind I got a copy of the firmware that came on my MS. I'm going to try to flash back tomorrow.
I downloaded the 3.3.0 flash and I used the boot jumper and followed all the on screen instructions from the command prompt. it seems to flash normal and doesnt give any other messages.
When I go to open the 3.3.0 base file the window says unrecognized file. and still gives the null error.
My next question is does anyone have the MS2/Extra pre-3.3 beta 16.20130822 firmware that I could have?
Update 2:
nevermind I got a copy of the firmware that came on my MS. I'm going to try to flash back tomorrow.
Last edited by zero415; 12-02-2013 at 09:29 PM.
#6
the base file is for the 1.6 miata 3.3.0 and this is after reflashed lastnight using the jumper pin and following the console commands.
Also, can somebody be clear with me on flashing the MSPNP2?
Do I need to have the boot jumper on when flashing to new or older firmware?
also in the command prompt, it gives 4 options the 4th being Microsquirt Case, microsquirt module and MSPNP I selected MSPNP when flashing 3.3.0, should i have used the Microsquirt module instead?
at this point, i have the beta firmware that came on my MSPNP and I can reflash back to that tonight.
#8
clicking yes gives a second error. I dont have a picture but this is the text that it gives.
Reported Error:
Problem parsing tune settings file (.msq):
The markup in the document following the root element must be well-formed.
Root problem: The markup in the document following the root element must be well-formed.
I downloaded the 3.3.0 firmware and selected other and put the MSPNP2.ini in there and tried to open the 3.3.0 basemap. below is the error
Update:
Phil from DIY responded by my e-mail stating that they had an issue with the website where the base maps are. Hopefully this is the issue with the 3.3.0 map. so I would watch downloading from megasquirtpnp.com for now.
Reported Error:
Problem parsing tune settings file (.msq):
The markup in the document following the root element must be well-formed.
Root problem: The markup in the document following the root element must be well-formed.
I downloaded the 3.3.0 firmware and selected other and put the MSPNP2.ini in there and tried to open the 3.3.0 basemap. below is the error
Update:
Phil from DIY responded by my e-mail stating that they had an issue with the website where the base maps are. Hopefully this is the issue with the 3.3.0 map. so I would watch downloading from megasquirtpnp.com for now.
Last edited by zero415; 12-03-2013 at 05:19 PM.
#9
I just went through this with Matt over at DIYAUTOTUNE - he sent me my basemap here: (This is for a 96' NA)
Hopefully the site will be uploaded soon.
https://www.dropbox.com/sh/jtf4vy54ezt2wwb/YWN6ThC7Xv
Hopefully the site will be uploaded soon.
https://www.dropbox.com/sh/jtf4vy54ezt2wwb/YWN6ThC7Xv
#17
Phil sent me another version of the 3.3.0 .msq for the 1.6 miata and i was able to open that msq file up in tuner studio.
Im in the process of uploading it to my dropbox and will update with the link when complete.
Update:
I have attached the file, but if you cant get it here is the alternate link to dropbox:
https://www.dropbox.com/s/yqj5cl9yeu...93%20Miata.msq
Thread
Thread Starter
Forum
Replies
Last Post