12" slim fan installation
http://cgi.ebay.com/ebaymotors/ws/eB...m=250291675413
Has anyone installed one of these in the passenger side (main fan) area? I installed a new pipe today, but the OEM FAN had to be removed to get it in. I was inquiring as to who might have one of these installed and did they fab up much to the radiator --- Or, is it best to get the 10" Slim Fan |
12" fits fine on the stock radiator...I used the little zip tie type things that come with the fans so it took ~5 minutes.
EDIT: Isn't the passenger's side the a/c fan not the main fan? |
Originally Posted by KPLAFIN
(Post 307096)
12" fits fine on the stock radiator...I used the little zip tie type things that come with the fans so it took ~5 minutes.
EDIT: Isn't the passenger's side the a/c fan not the main fan? I was thinking along the lines of what CUEBALL did in post #28 of this thread: (Maybe Aluminium) https://www.miataturbo.net/forum/sho...hlight=Fan+Mod Specific Post https://www.miataturbo.net/forum/sho...4&postcount=28 ZIP TIES, you say! === Taking lessons from our "LORD BRAINEACK" ? |
Originally Posted by LOLA - 92
(Post 307104)
I can't remember which one is the main, but it doesn't much matter. I had to remove the Pass. Fan (larger of the two).
I was thinking along the lines of what CUEBALL did in post #28 of this thread: https://www.miataturbo.net/forum/sho...hlight=Fan+Mod ZIP TIES, you say! === Taking lessons from our "LORD BRAINEACK" ? Not actual zip ties the "mounting kit" these come with: http://www.siliconeintakes.com/produ...f502a9a8c4df07 |
The big fan is on the Drivers' side.
|
Originally Posted by olderguy
(Post 307108)
The big fan is on the Drivers' side.
I just went into the garage and looked at them. BRUCE is right. Anyway, I need to replace the PASSENGER SIDE FAN. The shroud deminsions are 12x12 -- I wonder if I can get a Slim fit in there.... Thank You BRUCE for correcting my old age retardedness.... :giggle: |
Originally Posted by LOLA - 92
(Post 307109)
I just went into the garage and looked at them. BRUCE is right.
Thank You BRUCE for correcting my old age retardedness.... :giggle:
Originally Posted by LOLA - 92
(Post 307109)
I wonder if I can get a Slim fit in there....
|
Originally Posted by KPLAFIN
(Post 307110)
But...but...but...I was right and corrected you first.. :sadwavey:
I think Scott determined only a 10" would fit in the OEM shroud, but a 12" fan will fit in the spot w/ no shroud. KPLAFIN - Which side did you use that 10" on? Was there still room to go around? Like maybe the 12" fan? |
Then look at it this way...if the stock shroud in that spot is 12X12 then why wouldn't a 12" fan fit? IOW, yes a 12" slim fan will fit in that spot with no problem.
|
KPLAFIN --
WOW - Siliconeintakes.com only wants $33 to ship 6-10 days on USPS + the cost of the fan @ $30. Those guys are fuckin crazy = $33 for shipping from Co. to Fl. for a fan. I went with the EBAY one for $35 total cost. I'm crossin my digits.... Thanks Guys, LOLA |
I have the mishi rad. installed along with 2 12" slim ebay fans and they are both fitted using the stock fan shrouds. The A/C fan fits really tight, but does fit without any problems. I just used wire ties for the A/C fan.
|
What I did, building a shroud from ABS, did push them back. If I was bothered by that I could cut down the posts some or cut the ABS where the mounting posts are, heat it and bend the tabs to move the fans closer. Because of the shroud I certainly didn't gain much working room but I have much better cooling. Far better than with the stock fans and fixing the fans directly to the rad was a complete waste of time. Overheated the 1st hot day when they were installed that way. Shroud is absolutely the way to go. I just copied the one that fatcat sells only I used ABS sheet.
I bought 2 12" fans for $21.95 each, combined shipping was about $12. This is the store... http://stores.ebay.com/abad71camaro |
Originally Posted by cueball1
(Post 307123)
What I did, building a shroud from ABS, did push them back. If I was bothered by that I could cut down the posts some or cut the ABS where the mounting posts are, heat it and bend the tabs to move the fans closer. Because of the shroud I certainly didn't gain much working room but I have much better cooling. Far better than with the stock fans and fixing the fans directly to the rad was a complete waste of time. Overheated the 1st hot day when they were installed that way. Shroud is absolutely the way to go. I just copied the one that fatcat sells only I used ABS sheet.
There's a SUCKA BORN every day. (M-Tuned FTL) |
Originally Posted by LOLA - 92
(Post 307104)
ZIP TIES, you say! === Taking lessons from our "LORD BRAINEACK" ? they make special zip-ties for radiator fans....go to advanced auto where the oil coolers are, you'll see them. That fan posted above had a hard time raising the atmospheric pressure more than the stock fan could, based on my magenhellic gauge readings. |
Originally Posted by Braineack
(Post 307140)
they make special zip-ties for radiator fans....go to advanced auto where the oil coolers are, you'll see them.
That fan posted above had a hard time raising the atmospheric pressure more than the stock fan could, based on my magenhellic gauge readings. I ended up going to harbor freight and bought some metal zip ties. |
I hate reading this kind of shit the night before a track day...I may pack my stock fans in the trunk, just in case I over heat. that or I might try taking one off. or both. or driving my car into the wall in frustration.
I can switch my fans off at any time, would it be benifitial to shut them off while I'm racing to allow the air to pass by the fans better? |
Originally Posted by curly
(Post 307201)
or driving my car into the wall in frustration.
|
you would...
I have a hard dog hard core double diagonal. or HDHDCHCHDHCHDCHC to those who know the acronyms. |
Originally Posted by LOLA - 92
(Post 307117)
KPLAFIN --
WOW - Siliconeintakes.com only wants $33 to ship 6-10 days on USPS + the cost of the fan @ $30. Those guys are fuckin crazy = $33 for shipping from Co. to Fl. for a fan. I went with the EBAY one for $35 total cost. I'm crossin my digits.... Thanks Guys, LOLA Im in NY. |
All times are GMT -4. The time now is 03:14 PM. |
© 2024 MH Sub I, LLC dba Internet Brands