Manifold Crack Prevention
#1
Elite Member
Thread Starter
iTrader: (6)
Join Date: Sep 2007
Location: CA
Posts: 2,016
Total Cats: 13
Manifold Crack Prevention
So far, I've read that cracks w/ the Greddy manifold can be reduced by:
1) Large relief cuts.
2) Making sure that the mating surface on the exhaust manifold is flat.
3) Not using the hard bracket to tranny
4) Don't wrap the manifold
5) I read on m.net that someone put some sort of extra rubber bushing on the exhaust hangers to prevent them from flexing?
Is there anything else anyone can think of? Thanks.
1) Large relief cuts.
2) Making sure that the mating surface on the exhaust manifold is flat.
3) Not using the hard bracket to tranny
4) Don't wrap the manifold
5) I read on m.net that someone put some sort of extra rubber bushing on the exhaust hangers to prevent them from flexing?
Is there anything else anyone can think of? Thanks.
#2
Boost Pope
iTrader: (8)
Join Date: Sep 2005
Location: Chicago. (The less-murder part.)
Posts: 33,017
Total Cats: 6,587
Personal Opinion:
Making the three reflief cuts between the runner is probably the big-ticket item. When I removed the turbo and manifold a couple of months ago (for some unrelated work) I found that the cut between #2 and #3 had essentially closed up completely, so theres definitely some expansion taking place. I re-opened that cut by running the hacksaw blade down through it again- we'll see how it looks in another year or so.
In my case, I found it necessary to fabricate a hard bracket to the bellhosing bolts, since otherwise my 2.5" DP tended to bang into the frame. As it is I've only got about 1/4" clearance, but with the Mazdacomp mounts that seems to be enough.
It's been running like this for about a year and a half, and no cracks thus far.
YMMV.
Making the three reflief cuts between the runner is probably the big-ticket item. When I removed the turbo and manifold a couple of months ago (for some unrelated work) I found that the cut between #2 and #3 had essentially closed up completely, so theres definitely some expansion taking place. I re-opened that cut by running the hacksaw blade down through it again- we'll see how it looks in another year or so.
In my case, I found it necessary to fabricate a hard bracket to the bellhosing bolts, since otherwise my 2.5" DP tended to bang into the frame. As it is I've only got about 1/4" clearance, but with the Mazdacomp mounts that seems to be enough.
It's been running like this for about a year and a half, and no cracks thus far.
YMMV.
#5
Elite Member
Thread Starter
iTrader: (6)
Join Date: Sep 2007
Location: CA
Posts: 2,016
Total Cats: 13
Personal Opinion:
In my case, I found it necessary to fabricate a hard bracket to the bellhosing bolts, since otherwise my 2.5" DP tended to bang into the frame. As it is I've only got about 1/4" clearance, but with the Mazdacomp mounts that seems to be enough.
It's been running like this for about a year and a half, and no cracks thus far.
YMMV.
In my case, I found it necessary to fabricate a hard bracket to the bellhosing bolts, since otherwise my 2.5" DP tended to bang into the frame. As it is I've only got about 1/4" clearance, but with the Mazdacomp mounts that seems to be enough.
It's been running like this for about a year and a half, and no cracks thus far.
YMMV.
Joe, does your bracket flex or move at all?
#7
Boost Pope
iTrader: (8)
Join Date: Sep 2005
Location: Chicago. (The less-murder part.)
Posts: 33,017
Total Cats: 6,587
The first two flexed until they broke. The one that's on there now is made from 3/16" steel, and flexes less than not at all.
However, my DP is a two-piece unit, with a slip-coupling in the center. The rigid bracket is attached to a U-clamp that is installed after the coupling, so the upper section can move about a bit if it needs to. Between that and the catalytic converter is a flex section.
In this picture you can see the general design. That particular bracket is one that broke, but the current design is the same idea, just much thicker.
However, my DP is a two-piece unit, with a slip-coupling in the center. The rigid bracket is attached to a U-clamp that is installed after the coupling, so the upper section can move about a bit if it needs to. Between that and the catalytic converter is a flex section.
In this picture you can see the general design. That particular bracket is one that broke, but the current design is the same idea, just much thicker.
Thread
Thread Starter
Forum
Replies
Last Post