Pictures Finally!
Admittedly I don't know much about cars, ask Corky and Stephanie but I know less about computers so after 6 months of Flogging my BEGi Series 4 I finally figured out how to link pictures. I've already got Forged internals waiting in the garage so they will be going in soon! Enjoy my car!
www.cardomain.com/ride/3079155 |
Looks nice man. Very clean.
|
That's actually a pretty nice looking setup. I see you're aiming for 345 HP with the boost increase and forged internals. I don't know the exact numbers, but from what I recall the transmission becomes a weak point around 300HP. So keep that in mind.
|
I found out about the tranny the Hard Way! After an Autocross one day I drag raced (with my trailer still on) a guy in a C5 vette and when I shifted into second BAM! Bye Bye trans. :) I put in a 6 speed. I've also been through 4 rear tires since the install, two Fuzion 215/40 17" ZRi's and two Kumho 225/50 15" V710's. You won't hear me complain about excessive tire wear because I drive it like I stole it! Always! Thanks for the comments.
|
Clean!!!
|
Haha, I think the trailer is quite interesting.
The car looks awesome dude, but I definately would have to say that it drives even better then it looks. Which is really saying something. |
Harbor Freight trailor FTW! I love my little tag along.......;)
|
Damn, Man. That looks good! Nice numbers on 13psi too!! :D
|
In for 6-speed trans.
|
That's a lot of power. Shiny manifold and shiny car.
|
What are you using for engine management? I'm still torn between the FM II Hydra and the BEGi Stage 4. I am picking up my my mom's '99 with 25k miles on it this winter. :)
I plan on doing track days, so I like the idea of having the Hydra ecu for the ability to control everything. I come from a DSM background, so using an AEM is the norm for me... |
I've heard lots of good stuff about the AEM and Hydra but I've said it before, I AM WEE-TODD-DID when it comes to tuning so I'm probably going with a Tec III so mikef85 can tune it with/for me.:) Right Mike? I have the XEDE right now but Corky says that to go above 300rwhp I should go Stand-alone so I am.
|
Well I finally went and bent a Rod so it looks like the motor build will begin ASAP! Brandon at FM says that they have a 2.0 Stroker just sitting around so if it's available I may just be doing a motor swap and not a build.:)
|
Originally Posted by mattkock
(Post 328449)
Well I finally went and bent a Rod so it looks like the motor build will begin ASAP! Brandon at FM says that they have a 2.0 Stroker just sitting around so if it's available I may just be doing a motor swap and not a build.:)
|
That's super clean!
|
Originally Posted by mattkock
(Post 328449)
Well I finally went and bent a Rod so it looks like the motor build will begin ASAP! Brandon at FM says that they have a 2.0 Stroker just sitting around so if it's available I may just be doing a motor swap and not a build.:)
|
I'll be there! It's still running great, it just makes a cool ticking noise! :) Corky told me not to use my Rev-limiter as a shift point anymore until I build the motor. After the Dyno day I'm having everyone come back to my house for burgers and dogs and Miata stuff and then later that night, UFC!. I think the weather is supposed to be Great this weekend so everyone is welcome, Miata or not.
|
very nice
|
So is the 6-speed transmission much more solid than the 5-speeds? Given a strong clutch, how much horsepower can it hold compared to the 5-speed?
|
Yes, mine was reliable up to 400whp....but don't go past that.
I could bang the gears as much as I wanted at 400whp, but when I started tuning high boost it started to act up. |
All times are GMT -4. The time now is 04:37 PM. |
© 2024 MH Sub I, LLC dba Internet Brands