Miata Turbo Forum - Boost cars, acquire cats.

Miata Turbo Forum - Boost cars, acquire cats. (https://www.miataturbo.net/)
-   Race Prep (https://www.miataturbo.net/race-prep-75/)
-   -   RPM Limit (https://www.miataturbo.net/race-prep-75/rpm-limit-58198/)

falcon 06-01-2011 09:00 PM
RPM Limit
 
What are you track sluts running for RPM limits on built motors? What do you find is enough? Do you wish you had more? What transmission/final drive?

I'm running an 8000RPM limit right now but am considering dropping it down a bit so I can gear my Rotrex higher in the lower RPMS.

For those of you who don't frequent the supercharger sub-forum....


https://www.miataturbo.net/showthrea...575#post733575

Savington 06-01-2011 10:38 PM
6sp, 3.909, 7400rpm. Wish I had another 400rpm or so, but I need to change the intake cam first (VVT cam harmonic).

falcon 06-01-2011 11:03 PM
On 15's right? A 3.9 and 6spd should be comparable to a 4.1 and 5spd I think?

I recall at Knox I was shifting around 7K because it was all uphill and there was no torque after 7k. At AutoX, I tend to use all the RPMS because it's flat and my local track is flat so I think a 7600-7800 limit would be ideal. That would put me at about a 95mm pulley. Worst case I don't like it and I can always throw the old pulley back on and bump it back up. But I think 200RPM shouldn't bee too noticeable.

chicksdigmiatas 06-01-2011 11:28 PM
Originally Posted by Savington (Post 733611)
6sp, 3.909, 7400rpm. Wish I had another 400rpm or so, but I need to change the intake cam first (VVT cam harmonic).
What are the options for this. I will need the revs for auto x.

hustler 06-01-2011 11:44 PM
7000rpm for Mr. Reliabilitaur. I make torque and HP everywhere. Next time I'm going to set my cut at 6800rpm to lower my peak power numbers for classing.

Midtenn 06-02-2011 08:32 AM
Originally Posted by chicksdigmiatas (Post 733626)
What are the options for this. I will need the revs for auto x.
5spd and a 4.1 will give you a long enough 2nd gear. Short shift to third if need be.

chicksdigmiatas 06-02-2011 10:41 AM
Originally Posted by Midtenn (Post 733683)
5spd and a 4.1 will give you a long enough 2nd gear. Short shift to third if need be.

It doesn't. I have to do 2-3-2 shifts alot.

Savington 06-02-2011 10:45 AM
Originally Posted by falcon (Post 733620)
On 15's right? A 3.9 and 6spd should be comparable to a 4.1 and 5spd I think?

I recall at Knox I was shifting around 7K because it was all uphill and there was no torque after 7k. At AutoX, I tend to use all the RPMS because it's flat and my local track is flat so I think a 7600-7800 limit would be ideal. That would put me at about a 95mm pulley. Worst case I don't like it and I can always throw the old pulley back on and bump it back up. But I think 200RPM shouldn't bee too noticeable.
WTF, no torque after 7k? Don't you have a C30-94 on that car?

e: Just saw your S/C section thread, 14psi and you're only making 225whp from a C30-94?

6sp+3.9s is nothing like a 5sp and 4.1s. 6sp and 3.9s is probably closest to a 5sp and 4.44s, but still nothing like it since the 5-speed's 2nd and 3rd would be way shorter. 6sp+3.909+7400 is 80 in 3rd, 100 in 4th, 130 in 5th, and 155 in 6th. I would like another 5-7mph in 5th, and an additional ~8mph in 6th.

Braineack 06-02-2011 10:46 AM
how would a C30-94 not have any torque past 7K....isn't that the whole point of a centrifugal supercharger?

bbundy 06-02-2011 11:38 AM
Originally Posted by Savington (Post 733726)
WTF, no torque after 7k? Don't you have a C30-94 on that car?

e: Just saw your S/C section thread, 14psi and you're only making 225whp from a C30-94?

6sp+3.9s is nothing like a 5sp and 4.1s. 6sp and 3.9s is probably closest to a 5sp and 4.44s, but still nothing like it since the 5-speed's 2nd and 3rd would be way shorter. 6sp+3.909+7400 is 80 in 3rd, 100 in 4th, 130 in 5th, and 155 in 6th. I would like another 5-7mph in 5th, and an additional ~8mph in 6th.
He has a 1.6L

Bob

falcon 06-02-2011 12:15 PM
Originally Posted by Savington (Post 733726)
WTF, no torque after 7k? Don't you have a C30-94 on that car?

e: Just saw your S/C section thread, 14psi and you're only making 225whp from a C30-94?

6sp+3.9s is nothing like a 5sp and 4.1s. 6sp and 3.9s is probably closest to a 5sp and 4.44s, but still nothing like it since the 5-speed's 2nd and 3rd would be way shorter. 6sp+3.909+7400 is 80 in 3rd, 100 in 4th, 130 in 5th, and 155 in 6th. I would like another 5-7mph in 5th, and an additional ~8mph in 6th.
The intake manifold is causing a restriction. It's a 1.6L not a 1.8L. If you look at what power it's making at what RPM/boost it's not terrible but it could be more... 11PSI at 7k and 215whp, 9PSI at 6.5.K at 200whp, 8PSI at 6k at 180whp. When I am done with the new manifold/pulley I am going to do a pull on another dyno just to see if the dynapack is reading low. It feels pretty on part with a friends 260whp turbo miata he had.

chicksdigmiatas 06-02-2011 09:05 PM
Originally Posted by Savington (Post 733726)
WTF, no torque after 7k? Don't you have a C30-94 on that car?

e: Just saw your S/C section thread, 14psi and you're only making 225whp from a C30-94?

6sp+3.9s is nothing like a 5sp and 4.1s. 6sp and 3.9s is probably closest to a 5sp and 4.44s, but still nothing like it since the 5-speed's 2nd and 3rd would be way shorter. 6sp+3.909+7400 is 80 in 3rd, 100 in 4th, 130 in 5th, and 155 in 6th. I would like another 5-7mph in 5th, and an additional ~8mph in 6th.

6spd 3.636 = 5 speed 4.3 plus another gear.


All times are GMT -4. The time now is 04:26 AM.


© 2024 MH Sub I, LLC dba Internet Brands